2011 Subaru Outback LimitedFACTORY OEM SERVICE PROCEDURE

Transmission Control Module (TCM) Reprogramming File Availability For Inconsistent Engine Braking "Feel" (16-100-16)

Publication date: 2016-04-15
Reference number: 16-100-16

TRANSMISSION CONTROL MODULE (TCM) REPROGRAMMING FILE AVAILABILITY FOR INCONSISTENT ENGINE BRAKING "FEEL"

TRANSMISSION CONTROL MODULE (TCM) REPROGRAMMING FILE AVAILABILITY FOR INCONSISTENT ENGINE BRAKING "FEEL"

TECHNICAL SERVICE BULLETIN

Reference Number(s): 16-100-16, Date of Issue:  April 15, 2016
SUBARU: 2010-11 Legacy and Outback

APPLICABILITY

2010-11MY Legacy and Outback 2.5L NA Models

INTRODUCTION

This bulletin announces availability of reprogramming files to optimize the TCM. The files will address customer concerns of inconsistency in the amount of engine braking experienced when using Manual mode (or paddle shifters if equipped) when descending long downgrades.

PACK FILE APPLICABILITY

Model PAK File Name New TCM Part Number Old TCM Part Numbers Decryption Keyword New TCM CID Number
2010MY Legacy 30919AB014.pak 30919AB014 30919AB010, 011, 012 & 013 507E6259 Z5F3E083
2010MY Outback 30919AB024.pak 30919AB024 30919AB020, 021, 022 & 023 6933FF47 Z5F3E183
2011MY Legacy 30919AB673.pak 30919AB673 30919AB670, 671 & 672 C42507B4 Y6F3E082
2011MY Outback 30919AB683.pak 30919AB683 30919AB680, 681 & 682 AA9EF073 Y6F3E182

PACK FILE APPLICABILITY

  • Reprogram the TCM using the SSM4 following the normal FlashWrite procedure.
NOTE: SOA now highly recommends connecting the Midtronics GR8 Diagnostic Battery Charger to the vehicle and utilizing the Power Supply Mode feature anytime a vehicle control module is being reprogrammed. Once the GR8 is connected to the vehicle, as long as the battery is fully charged, it takes less than 3 minutes to boot-up the charger, select the Power Supply Mode, and have the battery voltage stabilized and ready for reprogramming.

VERY IMPORTANT:  This information is applicable to the Midtronics GR8 Diagnostic Battery Charger ONLY  . It does not apply to any other brand / type of "generic" battery charger whatsoever. ONLY  the GR8 and its Power Supply Mode feature has been tested and approved by Subaru of America, Inc. (SOA).

  • If the GR8 indicates the vehicle's battery must be charged, charge the battery using the GR8 before proceeding to reprogram the vehicle while using the Power Supply Mode.
  • Control module failures as a result of battery discharge during reprogramming are not a matter for warranty. Should any DTCs reset after the reprogramming update is performed, diagnose per the procedure outlined in the applicable Service Manual.

WARRANTY / CLAIM INFORMATION

For vehicles within the Basic New Car Limited or Powertrain Warranty period or covered by a Subaru Added Security Powertrain, Classic or Gold plan, this repair may be submitted using the following claim information:

Labor Description Labor Operation # Fail Code Labor Time
TCM Reprogramming A860-737 MJZ-48 0.4
IMPORTANT: The NEW  Calibration Identification number (CID) for any newly-installed programming (as confirmed from the actual control module AFTER  installation) MUST  be noted on the repair order as this information is required for claim submission.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.