Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2010 Subaru Outback F4-2.5L SOHCFACTORY OEM SERVICE PROCEDURE
Tightening Specifications
Cylinder Head Bolts

First pass 29 Nm (3.0 kgf-m, 21.4 ft-lb)
Second pass 69 Nm (7.0 kgf-m, 50.9 ft-lb)
Third pass: Loosen all bolts 180°
Fourth pass: Loosen all bolts 180°
Fifth pass 42 Nm (4.3 kgf-m, 31.0 ft-lb)
Sixth pass: Tighten 80-90°
Seventh pass: Tighten 40-45°
Final pass: Tighten bolts (a) and (b) 40-45°
Camshaft Bearing Cap Bolts
Please refer to Camshaft Removal and Replacement for camshaft bearing cap bolt tightening specifications and procedure. Service and Repair
Crankshaft Main Bearing Cap Bolts
Please refer to Cylinder Block Assembly Removal and Replacement for bolt tightening specifications and sequence. Service and Repair
Connecting Rod Cap Fasteners 45 Nm (4.6 kgf-m, 33.2 ft-lb)
Crank Sprocket Bolt 24.5 Nm (2.5 kgf-m, 18.1 ft-lb)
Crank Pulley Bolt
First pass 47 Nm (4.8 kgf-m, 34.7 ft-lb)
Final pass Tighten 60° ± 5°
Oil Pump Bolts 6.4 Nm (0.7 kgf-m, 4.7 ft-lb)
Front Exhaust Pipe to Cylinder Head Nuts 30 Nm (3.1 kgf-m, 22.1 ft-lb)
Water Pump Bolts

First pass 29 Nm (3.0 kgf-m, 21.4 ft-lb)
Second pass 69 Nm (7.0 kgf-m, 50.9 ft-lb)
Third pass: Loosen all bolts 180°
Fourth pass: Loosen all bolts 180°
Fifth pass 42 Nm (4.3 kgf-m, 31.0 ft-lb)
Sixth pass: Tighten 80-90°
Seventh pass: Tighten 40-45°
Final pass: Tighten bolts (a) and (b) 40-45°
Camshaft Bearing Cap Bolts
Please refer to Camshaft Removal and Replacement for camshaft bearing cap bolt tightening specifications and procedure. Service and Repair
Crankshaft Main Bearing Cap Bolts
Please refer to Cylinder Block Assembly Removal and Replacement for bolt tightening specifications and sequence. Service and Repair
Connecting Rod Cap Fasteners 45 Nm (4.6 kgf-m, 33.2 ft-lb)
Crank Sprocket Bolt 24.5 Nm (2.5 kgf-m, 18.1 ft-lb)
Crank Pulley Bolt
First pass 47 Nm (4.8 kgf-m, 34.7 ft-lb)
Final pass Tighten 60° ± 5°
Oil Pump Bolts 6.4 Nm (0.7 kgf-m, 4.7 ft-lb)
Front Exhaust Pipe to Cylinder Head Nuts 30 Nm (3.1 kgf-m, 22.1 ft-lb)
Water Pump Bolts
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
