2010 Subaru Forester X, AutomaticFACTORY OEM SERVICE PROCEDURE

Select Lever: Disassembly

  1. Remove the gasket and plate COMPL.
    2. Fig 1: Identifying Gasket And Plate COMPL
    G05661193Courtesy of SUBARU OF AMERICA, INC.
  2. Insert a flat-tip screwdriver with a thin tip under the connector and disconnect each connector from the plate COMPL.
    3. Fig 2: Disconnecting Connector From Plate COMPL
    G05661194Courtesy of SUBARU OF AMERICA, INC.
  3. Remove the spacer bolt and remove the plate guide COMPL.
    4. Fig 3: Identifying Spacer Bolt And Plate Guide COMPL
    G05661195Courtesy of SUBARU OF AMERICA, INC.
  4. Remove the shift lock clamp, spring A, select lever rod, lock plate cushion, and bushing.
    5. Fig 4: Identifying Shift Lock Clamp, Spring A, Select Lever Rod, Lock Plate Cushion, And Bushing
    G05955796Courtesy of SUBARU OF AMERICA, INC.
  5. Remove the bracket.
    6. Fig 5: Identifying Bracket
    G05661197Courtesy of SUBARU OF AMERICA, INC.
  6. Remove the detent spring.
    7. Fig 6: Identifying Detent Spring
    G05661198Courtesy of SUBARU OF AMERICA, INC.
  7. Remove the shift lock solenoid unit.
    8. Fig 7: Removing Shift Lock Solenoid Unit
    G05661200Courtesy of SUBARU OF AMERICA, INC.
  8. Raise the claw of connector.
    9. Fig 8: Raising Claw Of Connector
    G05019677Courtesy of SUBARU OF AMERICA, INC.
  9. Disconnect the terminals of the SPORT mode switch, "P" range switch, and shift lock solenoid from the connector, using a flat-tip screwdriver with a thin tip.
    10. Fig 9: Identifying Shift Lock Solenoid Terminals
    G05955801Courtesy of SUBARU OF AMERICA, INC.
  10. Remove the grommet.
    11. Fig 10: Identifying Grommet
    G05661203Courtesy of SUBARU OF AMERICA, INC.
  11. Remove the spring pin.
    12. Fig 11: Identifying Spring Pin
    G05661204Courtesy of SUBARU OF AMERICA, INC.
  12. Pull out the arm assembly, remove select lever COMPL, and remove bracket arm detent and bushing.
    13. Fig 12: Identifying Arm Assembly, Select Lever COMPL, Bracket Arm Detent And Bushing
    G05955804Courtesy of SUBARU OF AMERICA, INC.
  13. Remove the rod detent and spring detent from the bracket arm detent.
Fig 13: Identifying Rod Detent, Spring Detent And Bracket Arm Detent
G05955805Courtesy of SUBARU OF AMERICA, INC.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.