Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2009 Subaru Outback F4-2.5L SOHCFACTORY OEM SERVICE PROCEDURE
System Specifications
Cylinder head bolts
Tighten all bolts 29 N-m (3.0 kgf-m, 21.4 ft-lb)
Tighten all bolts 69 N-m (7.0 kgf-m, 50.9 ft-lb)
Loosen all 180°
(in the reverse order)
Loosen further 180°
Tighten all 42 N-m (4.3 kgf-m, 31.0 ft-lb)
Tighten all 80 to 90°
Tighten all 40 to 45°
Further tighten (a) and (b) 40 - 45°

Cylinder head
Surface warping limit 0.035 mm (0.0014 in)
Grinding limit 0.1 mm (0.004 in)
Standard height 97.5 mm (3.84 in)
Camshaft Cap
Temporarily tighten the bolts (a) through (d)

TORX bolts through (j) 18 N-m (1.8 kgf-m, 13.3 ft-lb)

Bolts (k) through (r) 9.75 N-m (1.0 kgf-m, 7.2 ft-lb)

Bolts (s) and (t) 9.75 N-m (1.0 kgf-m, 7.2 ft-lb)

Cam Sprocket 78 N-m (8.0 kgf-m, 57.5 ft-lb)
Tighten all bolts 29 N-m (3.0 kgf-m, 21.4 ft-lb)
Tighten all bolts 69 N-m (7.0 kgf-m, 50.9 ft-lb)
Loosen all 180°
(in the reverse order)
Loosen further 180°
Tighten all 42 N-m (4.3 kgf-m, 31.0 ft-lb)
Tighten all 80 to 90°
Tighten all 40 to 45°
Further tighten (a) and (b) 40 - 45°
Cylinder head
Surface warping limit 0.035 mm (0.0014 in)
Grinding limit 0.1 mm (0.004 in)
Standard height 97.5 mm (3.84 in)
Camshaft Cap
Temporarily tighten the bolts (a) through (d)
TORX bolts through (j) 18 N-m (1.8 kgf-m, 13.3 ft-lb)
Bolts (k) through (r) 9.75 N-m (1.0 kgf-m, 7.2 ft-lb)
Bolts (s) and (t) 9.75 N-m (1.0 kgf-m, 7.2 ft-lb)
Cam Sprocket 78 N-m (8.0 kgf-m, 57.5 ft-lb)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
