Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2009 Subaru Forester XTFACTORY OEM SERVICE PROCEDURE
Key Interlock Cannot Be Locked Or Released
KEY INTERLOCK INSPECTION PROCEDURE
| Step | Check | Yes | No |
|---|---|---|---|
| 1 CHECK DELIVERY (TEST) MODE CONNECTORÂ
. Check that the delivery (test) mode connector is disconnected. |
Is the delivery (test) mode connector disconnected? | Go to step 2Â . | Disconnect the delivery (test) mode connector. |
| 2 CHECK BODY INTEGRATED UNIT POWER SUPPLY AND GROUND CIRCUITÂ Refer to BODY INTEGRATED UNIT POWER SUPPLY AND GROUND CIRCUITÂ , INSPECTION, AT Shift Lock Control System . |
Is there an abnormal condition? | Follow the procedures to inspect and repair. | Go to step 3Â . |
3 CHECK CURRENT DATAÂ
.
|
Is the display "ON" in the P range and "OFF" in ranges other than P? | Go to step 4Â . | Go to step 7Â . |
4 CHECK CURRENT DATAÂ
.
|
Does the display change from "ON" to "OFF" when the key is inserted and removed? | Go to step 5Â . | Go to step 10Â . |
5 CHECK CURRENT DATAÂ
.
|
Is the display "ON" in the P range and "OFF" in ranges other than P? | Go to step 12Â . | Go to step 6Â . |
6 CHECK DTC OF BODY INTEGRATED UNITÂ
.
|
Is B1105 (key interlock circuit malfunction) a current malfunction? | Follow the DTC to perform inspection and repair. | Go to step 11Â . |
7 CHECK HARNESS BETWEEN BODY INTEGRATED UNIT AND "P" RANGE SWITCHÂ
.
Connector & terminal (B281) No. 4 - (B117) No. 1: |
Is it less than 10 Ω? | Go to step 8 . | Repair or replace the harness between the body integrated unit and the "P" range switch. |
| 8 CHECK HARNESS BETWEEN "P" RANGE SWITCH AND CHASSIS GROUNDÂ
. Measure the resistance of harness between "P" range switch and chassis ground. Connector & terminal (B117) No. 2 - Chassis ground: |
Is it less than 10 Ω? | Go to step 9 . | Repair the harness between the "P" range switch and chassis ground. |
| 9 CHECK "P" RANGE SWITCHÂ
. Measure the resistance between "P" range switch connector terminals. Terminals No. 2 - No. 1: |
Is it less than 10 Ω in the "P" range, and 1 MΩ or more in ranges other than "P"? | Replace the body integrated unit. | Replace the "P" range switch. |
10 CHECK HARNESS BETWEEN BATTERY AND KEY WARNING SWITCH AND BODY INTEGRATED UNITÂ
.
Connector & terminal (B279) No. 2 - Chassis ground: |
Is the display 9 V or more when the key is inserted, and less than 1.5 V with the key removed? | Replace the body integrated unit. | Check the following items.
|
11 CHECK DELIVERY (TEST) MODE CONNECTOR HARNESSÂ
.
Connector & terminal (I84) No. 17 - (I1) No. 1: |
Is it less than 10 Ω? | Go to step 12 . | Repair or replace the harness between the body integrated unit connector and delivery (test) mode connector. |
12 CHECK HARNESS BETWEEN KEY LOCK SOLENOIDS AND BODY INTEGRATED UNITÂ
.
Connector & terminal (B279) No. 11 - (B350) No. 2: |
Is it less than 10 Ω? | Go to step 13 . | Repair or replace the harness between the body integrated unit and the key lock solenoid. |
| 13 CHECK HARNESS BETWEEN KEY LOCK SOLENOID AND CHASSIS GROUNDÂ
. Measure the resistance of harness between key lock solenoid and chassis ground. Connector & terminal (B350) No. 1 - Chassis ground: |
Is it less than 10 Ω? | Go to step 14 . | Repair or replace the harness between the key lock solenoid and chassis ground. |
| 14 CHECK KEY LOCK SOLENOID OPERATIONÂ
. Connect the battery to the key lock solenoid connector terminal, and operate the solenoid. |
Does the key lock solenoid operate normally? | Go to step 15Â . | Replace the key lock solenoid. |
15 CHECK OUTPUT OF BODY INTEGRATED UNITÂ
.
Connector & terminal (B279) No. 11 - Chassis ground: |
Is it 5 V or more in ranges other than "P", and less than 1.5 V in the "P" range? | Check the lock mechanism of the steering lock body. | Replace the body integrated unit. |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
