Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Key Interlock Cannot Be Locked Or Released
| Step | Check | Yes | No |
|---|---|---|---|
1 CHECK INPUT SIGNAL OF BODY INTEGRATED UNIT USING SUBARU SELECT MONITOR.Ā
|
Is "ON" displayed when the key is inserted and displayed "OFF when removed? | Go to step 7.Ā | Go to step 2.Ā |
2 CHECK HARNESS BETWEEN BATTERY AND KEY WARNING SWITCH.Ā
|
Is the voltage 9 - 16 V? | Go to step 3.Ā | Repair the open or short circuit of harness between battery and key warning switch. |
| 3 CHECK HARNESS BETWEEN KEY WARNING SWITCH AND BODY INTEGRATED UNIT.Ā Measure the resistance between key warning switch and body integrated unit. Connector & terminalĀ (B281) No. 7 - (B350) No. 4:Ā |
Is the resistance less than 1 Ī©? | Go to step 4.Ā | Repair the open circuit of harness between key warning switch connector and body integrated unit. |
| 4 CHECK HARNESS BETWEEN KEY WARNING SWITCH AND BODY INTEGRATED UNIT.Ā Measure the resistance of harness between key warning switch and chassis ground. Connector & terminalĀ (B281) No. 7 - Chassis ground:Ā |
Is the resistance 1 MĪ© or more? | Go to step 5.Ā | Repair the short circuit of harness between key warning switch and chassis ground. |
| 5 CHECK KEY WARNING SWITCH.Ā Measure the resistance between connector terminals of key warning switch. TerminalsĀ No. 3 - No. 4:Ā |
Is the resistance 1 MĪ© or more? | Replace the key warning switch. | Go to step 6.Ā |
6 CHECK KEY WARNING SWITCH.Ā
|
Is the resistance 1 MĪ© or more? | Replace the body integrated unit. | Replace the key warning switch. |
| 7 CHECK IGNITION POWER.Ā | Is the voltage 9 V or more? | Go to step 8.Ā | Check the ignition switch harness. |
8 CHECK DTC OF BODY INTEGRATED UNIT.Ā
|
Is B1105 current malfunction? | Repair or replace it according to the DTC. | Go to step 9.Ā |
| 9 CHECK INPUT SIGNAL OF BODY INTEGRATED UNIT USING SUBARU SELECT MONITOR.Ā Read the input signal of "P" range switch from the Subaru Select Monitor. < Ref. to OPERATION , Subaru Select Monitor . > |
Is "ON" displayed in the "P" range and displayed "OFF except in the "P" range? | Go to step 14.Ā | Go to step 10.Ā |
10 CHECK HARNESS BETWEEN BODY INTEGRATED UNIT AND "P" RANGE SWITCH.Ā
|
Is the resistance 1 MĪ© or more? | Repair the open circuit of harness between the body integrated unit and the "P" range switch. | Go to step 11.Ā |
| 11 CHECK HARNESS BETWEEN "P" RANGE SWITCH AND CHASSIS GROUND.Ā Measure the resistance of harness between "P" range switch and chassis ground. Connector & terminalĀ (B116) No. 2 - Chassis ground:Ā |
Is the resistance 1 MĪ© or more? | Repair the open circuit of harness between "P" range switch and chassis ground. | Go to step 12.Ā |
12 CHECK "P" RANGE SWITCH.Ā
|
Is the resistance less than 1 Ī©? | Go to step 13.Ā | Replace the "P" range switch. |
13 CHECK "P" RANGE SWITCH.Ā
|
Is the resistance 1 MĪ© or more? | Replace the body integrated unit. | Replace the "P" range switch. |
14 CHECK TEST MODE CONNECTOR.Ā
|
Is the resistance 1 MĪ© or more? | Go to step 15.Ā | Repair the short circuit of the harness between the body integrated unit and test mode connector. |
| 15 CHECK HARNESS BETWEEN KEY LOCK SOLENOID AND BODY INTEGRATED UNIT.Ā Measure the resistance between key lock solenoid and body integrated unit. TerminalsĀ (B280) No. 5 - (B350) No. 2:Ā |
Is the resistance less than 1 Ī©? | Go to step 16.Ā | Repair the open circuit of harness between key lock solenoid connector and body integrated unit. |
| 16 CHECK HARNESS BETWEEN KEY LOCK SOLENOID AND CHASSIS GROUND.Ā Measure the resistance of harness between key lock solenoid and chassis ground. TerminalsĀ (B280) No. 5 - Chassis ground:Ā |
Is the resistance 1 MĪ© or more? | Go to step 17.Ā | Repair short circuit of harness between key lock solenoid and chassis ground. |
17 CHECK KEY LOCK SOLENOID.Ā
|
Is the resistance between 12.5 - 14.5 Ī©? | Go to step 18.Ā | Replace the key lock solenoid. |
18 CHECK KEY LOCK SOLENOID.Ā
|
Does the key lock solenoid operate normally? | Go to step 19.Ā | Replace the key lock solenoid. |
19 CHECK INPUT SIGNAL OF BODY INTEGRATED UNIT USING SUBARU SELECT MONITOR.Ā
|
Is "OFF displayed in the "P" range and displayed "ON" except in the "P" range? | Go to step 20.Ā | Replace the body integrated unit. |
20 CHECK HARNESS BETWEEN BATTERY AND BODY INTEGRATED UNIT.Ā
|
Is the voltage 9 V or more? | Replace the body integrated unit. | Check the harness for open between the body integrated unit and battery or the fuse (No. 14). |
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- ⢠You smell fuel, burning insulation, or see smoke.
- ⢠Brakes feel soft, pull hard to one side, or make grinding noises.
- ⢠The engine overheats, stalls repeatedly, or misfires under load.
- ⢠You are missing required tools, torque specs, or safe lifting equipment.
- ⢠You are not confident in the next step or safety outcome.
