2008 Subaru Outback Base, AutomaticFACTORY OEM SERVICE PROCEDURE

Select Cable: Installation

WARNING: This page is about a different car, the 2007 Subaru Outback and 2007 Subaru Legacy. However, it is still accessible from the selected car via links, so may be relevant.
  1. Install the select cable to plate assembly.

    Tightening torque: 18 N.m (1.8 kgf-m, 13.3 ft-lb) 

    Fig 1: Identifying Select Cable Bolt Tightening Torque
    G05019691Courtesy of SUBARU OF AMERICA, INC.
  2. Install the select cable to range select lever.
  3. Install the plate assembly to transmission.

    Tightening torque: T: 24.5 N.m (2.5 kgf-m, 18.1 ft-lb) 

    • 4AT
      Fig 2: Identifying Plate Assembly Bolt Tightening Torque - 4AT
      G05341826Courtesy of SUBARU OF AMERICA, INC.
    • 5AT
      Fig 3: Identifying Plate Assembly Bolt Tightening Torque - 5AT
      G05341827Courtesy of SUBARU OF AMERICA, INC.
  4. Install the washer and snap pin to range select lever.
    • 4AT
      Fig 4: Identifying Range Select Lever Washer And Snap Pin - 4AT
      G05341828Courtesy of SUBARU OF AMERICA, INC.
    • 5AT
      Fig 5: Identifying Range Select Lever Washer And Snap Pin - 5AT
      G05341829Courtesy of SUBARU OF AMERICA, INC.
  5. Install new clamp paying attention to the installing direction.
    Fig 6: Installing Clamp Paying Attention To Installing Direction
    G05341830Courtesy of SUBARU OF AMERICA, INC.
  6. Insert the tip of inner cable into connector hole of select lever, and fix the cable to bracket.
    Fig 7: Inserting Tip Of Inner Cable Into Connector Hole Of Select Lever
    G05019697Courtesy of SUBARU OF AMERICA, INC.
  7. Shift the select lever to the "N" range, and then adjust the select cable position. <Ref. to ADJUSTMENT  , Select Cable .>
  8. Install the heat shield cover.
    Fig 8: Identifying Heat Shield Cover
    G05019661Courtesy of SUBARU OF AMERICA, INC.
  9. Install the front, center and rear exhaust pipes, and the muffler. (SOHC and DOHC non-turbo model)
  10. Install the center, rear exhaust pipes and the muffler. (DOHC turbo model) <Ref. to INSTALLATION , Center Exhaust Pipe .> <Ref. to INSTALLATION , Rear Exhaust Pipe .> <Ref. to INSTALLATION , INSTALLATION, Muffler .>
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.