2006 Subaru Outback RFACTORY OEM SERVICE PROCEDURE

AT Main Case: Installation

  1. Install the reverse brake piston.
    NOTE: Apply ATF onto the piston sliding surface.

    ST1 18762AA000 COMPRESSOR SPECIAL TOOL

    ST2 18765AA000 COMPRESSOR SUPPORT

    ST3 18763AA000 COMPRESSOR SHAFT

  2. Install the return spring.
    Fig 1: Identifying Return Spring
    G05022404
  3. Install the spring retainer and snap ring.

    ST1 18762AA000 COMPRESSOR SPECIAL TOOL

    ST2 18765AA000 COMPRESSOR SUPPORT

    ST3 18763AA000 COMPRESSOR SHAFT

    Fig 2: Identifying Spring Retainer And Snap Ring
    G05022402
  4. Install the dish plate.
    NOTE: When installing, make sure that the identification mark is facing the front side of transmission.
  5. Install the drive plate and driven plate.
  6. Install the leaf spring.
    Fig 3: Identifying Leaf Spring
    G05022409
  7. Install the retaining plate.
  8. Install the snap ring of the reverse brake.
    Fig 4: Identifying Snap Ring And Reverse Brake
    G05022400
  9. Perform the clearance check of reverse brake.
    1. Measure the clearance between retainer plate and snap ring using thickness gauge.

      Standard value: 0.7 - 1.1 mm (0.028 - 0.043 in)Β 

      Fig 5: Identifying Clearance Between Retainer Plate And Snap Ring
      G05022411
    2. If it is out of specification, select a suitable retainer plate from the following table and assemble it.
      THICKNESS CHART

      Retainer plate
      Part number Thickness mm (in)
      31567AB100 4.2(0.165)
      31567AB170 4.4(0.173)
      31567AB180 4.6(0.181)
      31567AB190 4.8(0.189)
      31567AB200 5.0(0.197)
  10. Install the direct clutch assembly.
    Fig 6: Identifying Direct Clutch Assembly
    G05022399
  11. Install the high & low reverse clutch assembly.
    Fig 7: Identifying Low Reverse Clutch Assembly
    G05022398
  12. Install the thrust needle bearing of the high & low reverse clutch.
    Fig 8: Identifying Thrust Needle Bearing Of High And Low Reverse Clutch
    G05022397
  13. Install the middle & rear sun gear assembly.
    Fig 9: Identifying Rear Sun Gear Assembly
    G05022396
  14. Install the rear carrier assembly.
    Fig 10: Identifying Rear Carrier Assembly
    G05022395
  15. Install the middle carrier assembly.
    Fig 11: Identifying Middle Carrier Assembly
    G05022394
  16. Install the thrust needle bearing of middle carrier assembly.
    Fig 12: Identifying Thrust Needle Bearing Of Middle Carrier Assembly
    G05022393
  17. Measure the total end play, and select the bearing. < Ref. to ADJUSTMENTΒ , AT Main Case. >
  18. Install the impact clutch pack assembly to oil pump cover.
    Fig 13: Identifying Impact Clutch Pack Assembly And Oil Pump Cover
    G05022419
  19. Turn the transmission sideways.
  20. Install the oil pump cover.
    1. Apply ATF to the O-ring of input clutch shaft.
    2. Install the oil pump cover to AT main case while supporting the input clutch shaft and oil pump housing with your hand.
      Fig 14: Removing Oil Pump Cover
      G05022392
    3. Make sure the rear end of drive pinion shaft is engaged to the spline of reduction driven gear.
      Fig 15: Identifying Drive Pinion Shaft
      G05022421
    4. Protect the input clutch shaft with a cloth, and rotate to engage the spline of the input clutch and rear carrier using pliers.
      NOTE: Work with pressing the oil pump cover.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.