Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2006 Subaru Outback RFACTORY OEM SERVICE PROCEDURE
Read Current Data
- On the «Main Menu» display screen, select the {Each System Check} and press the [YES] key.
- On the «System Selection Menu» display screen, select the {Transmission Control System} and press the [YES] key.
- Press the [YES] key after the information of transmission type is displayed.
- On the «Transmission Diagnosis» display screen, select the {Current Data Display & Save} and press the [YES] key.
- On the «Transmission Diagnosis» display screen, select the {Data Display} and press the [YES] key.
- Using the scroll key, scroll the display screen up or down until the desired data is shown.
- A list of the support data is shown in the following table.
RESISTANCE REFERENCE CHART
| Item | Display | Unit of measure |
|---|---|---|
| Engine speed signal | Engine Speed | rpm |
| Battery voltage | Battery Voltage | V |
| Accelerator position sensor | Acceleration Opening Angle | % |
| Front vehicle speed sensor signal | Front Wheel Speed | km/h |
| Gear position | Gear Position | - |
| Turbine speed sensor signal | Turbine Revolution Speed | rpm |
| Rear vehicle speed sensor signal | Rear Wheel Speed | km/h |
| Lateral G sensor | Lateral G Sensor | V |
| ATF temperature sensor 1 signal | ATF Temp. | °C |
| ATF temperature sensor 2 signal | ATF Temp. 2 | °c |
| Turbine speed sensor 1 signal | Turbine Revolution Speed 1 | rpm |
| Turbine speed sensor 2 signal | Turbine Revolution Speed 2 | rpm |
| High & low reverse clutch solenoid indicator current | H&LR/C Solenoid Current | A |
| Direct clutch solenoid indicator current | D/C Solenoid Current | A |
| Front brake solenoid indicator current | F/B Solenoid Current | A |
| Input clutch solenoid indicator current | I/C Solenoid Current | A |
| Line pressure solenoid indicator current | P/L Solenoid Current | A |
| Lock up solenoid indicator current | L/U Solenoid Current | A |
| Transfer solenoid indicator current | AWD Solenoid Current | A |
| High & low reverse clutch solenoid target oil pressure | H&LR/C Solenoid Target Pressure | kPa |
| Direct clutch solenoid target oil pressure | D/C Solenoid Target Pressure | kPa |
| Front brake solenoid target oil pressure | F/B Solenoid Target Pressure | kPa |
| Input clutch solenoid target oil pressure | I/C Solenoid Target Pressure | kPa |
| Line pressure solenoid target oil pressure | P/L Solenoid Target Pressure | kPa |
| Lock up solenoid target oil pressure | L/U Solenoid Target Pressure | kPa |
| Transfer solenoid target oil pressure | AWD Solenoid Target Pressure | kPa |
| Ignition switch | Ignition Switch | ON Input or OFF Input |
| Tip signal | Tiptronic Mode Switch | ON or OFF |
| Cruise control ON signal | Cruise Control Signal | ON or OFF |
| Tip down shift signal | Down SW | ON or OFF |
| Stop light switch signal | Stop Light SW | ON or OFF |
| Tip up shift signal | Up SW | ON or OFF |
| Drive range signal | D Range Signal | ON or OFF |
| Reverse range signal | R Range Signal | ON or OFF |
| Diagnosis light output signal | Diagnosis Light | ON or OFF |
| ATF temperature light signal | ATF Temperature Light | ON or OFF |
| Shift lock solenoid signal | Shift Lock Solenoid | ON or OFF |
| Parking range signal | P Range Signal | ON or OFF |
| P/N range output signal | P/N Signal | ON or OFF |
| Neutral range signal | N Range Signal | ON or OFF |
| Inhibitor switch 1 input signal | Inhibitor SW1 | High or Low |
| Inhibitor switch 2 input signal | Inhibitor SW2 | High or Low |
| Inhibitor switch 3 input signal | Inhibitor SW3 | High or Low |
| Inhibitor switch 4 input signal | Inhibitor SW4 | High or Low |
| Inhibitor switch 3 monitor input signal | Inhibitor SW3 Monitor | High or Low |
| Backup light relay output signal | Back-up light relay | ON or OFF |
| High & low reverse clutch oil pressure switch input signal | H&LR/C Oil Pressure SW | ON or OFF |
| Direct clutch oil pressure switch input signal | D/C Oil Pressure SW | ON or OFF |
| Front brake oil pressure switch input signal | FR/B Oil Pressure SW | ON or OFF |
| Input clutch oil pressure switch input signal | I/C Oil Pressure SW | ON or OFF |
| Low coast brake oil pressure switch input signal | LC/B Oil Pressure SW | ON or OFF |
| Low coast brake solenoid input signal | LC B Solenoid | ON or OFF |
NOTE:
For details concerning the operation procedure, refer to the "Subaru Select Monitor Operation Manual".
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
