Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2006 Subaru Outback RFACTORY OEM SERVICE PROCEDURE
Front Suspension: General Description: Specification
CHASSIS SPECIFICATION
| Model | Sedan | Wagon | ||||||
|---|---|---|---|---|---|---|---|---|
| 2.5 i | 2.5 GT | OUTBACK | 2.5 i | 2.5 GT | OUTBACK | |||
| Front | Wheel arch height [Tolerance:+12 mm-24 mm mm (+0 47 in-0 94 in )] |
mm (in) | 381 (15.0) | 439(17.3) | 381 (15.0) | 439(17.3) | ||
| Camber (Tolerance: °0°45' Differences between RH and LH: 45' or less) | -0°15' | 0°40' | -0°15' | 0°40' | ||||
| Caster (Referential Value) | 5°55' | 4°55' | 5°40' | 4°55' | ||||
| Steering angle (Tolerance: +/-1.5°) |
Inner wheel | 37.2° | 38.0° | 37.2° | 38.0° | |||
| Outer wheel | 33.0° | 33.7° | 33.0° | 33.7° | ||||
| Toe-in | mm (in) | 0+/-3 (0+/-0.12) Toe angle (sum of both wheels): 0°+/-0°15' | ||||||
| Kingpin angle (Referential Value) | 13°45' | 12°05' | 13°45' | 12°05' | ||||
| Diameter of stabilizer | mm (in) | 20 (0.79) | 21 (0.83) | 20 (0.79) | 21 (0.83) | |||
| Rear | Wheel arch height [Tolerance:+12 mm-24 mm (+0.47 in-0 94 in )] |
mm (in) | 365 (14.4) | 438 (17.2) | 375 (14.8) | 438 (17.2) | ||
| Camber (Tolerance: +/-0°45' Differences between RH and LH: 45' or less) | -0°40' | -0°10' | -0°30' | -0°10' | ||||
| Toe-in | mm (in) | 0+/-3 (0+0.12) Toe angle (sum of both wheels): 0°+/-0°15' | ||||||
| Thrust angle (Tolerance: +/-0°30') | 0° | |||||||
| Diameter of stabilizer | mm (in) | 15(0.59) | 16(0.63) | 15(0.59) | 16(0.63) | 15(0.59) | ||
NOTE:
- Front and rear toe-ins and front camber can be adjusted. If the toe-in or camber tolerance exceeds specifications, adjust them.
- Other items indicated in the specification table cannot be adjusted. If those items exceed specifications, check suspension parts and connections for deformities; replace with new ones as required.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
