2005 Subaru Outback i, StandardFACTORY OEM SERVICE PROCEDURE

Intake Manifold: Disassembly

  1. Disconnect the engine ground terminal from intake manifold.
    Fig 1: Disconnecting Engine Ground Terminal From Intake Manifold
    G03827658Courtesy of SUBARU OF AMERICA, INC.
  2. Remove the ignition coil & ignitor ASSY. < Ref. to REMOVAL , Ignition Coil and Ignitor Assembly. >
  3. Remove the throttle body. < Ref. to , REMOVAL , Throttle Body. >
  4. Remove the EGR valve. < Ref. to , REMOVAL , EGR Valve. >
  5. Remove the PCV pipe.
    Fig 2: Removing PCV Pipe
    G03827659Courtesy of SUBARU OF AMERICA, INC.
  6. Remove the fuel pipe protector LH.
    Fig 3: Removing Fuel Pipe Protector LH
    G03827660Courtesy of SUBARU OF AMERICA, INC.
  7. Remove the fuel pipe protector RH.
    Fig 4: Removing Fuel Pipe Protector RH
    G03827661Courtesy of SUBARU OF AMERICA, INC.
  8. Disconnect the pressure regulator vacuum hose (A) from intake manifold.
    Fig 5: Disconnecting Pressure Regulator Vacuum Hose (A) From Intake Manifold
    G03827662Courtesy of SUBARU OF AMERICA, INC.
  9. Disconnect the connectors (A) from fuel injector.
  10. Remove the clip (B) which holds engine harness to injector pipe.
    Fig 6: Removing Clip (B) Holding Engine Harness To Injector Pipe
    G03827663Courtesy of SUBARU OF AMERICA, INC.
  11. Remove the purge control solenoid valve. < Ref. to REMOVAL , Purge Control Solenoid Valve. >
  12. Remove the harness band clips which install the engine harness.
    Fig 7: Removing Harness Band Clips Which Install Engine Harness
    G03827664Courtesy of SUBARU OF AMERICA, INC.
  13. Remove the bolts which hold the engine harness to intake manifold.
    Fig 8: Removing Bolts Holding Engine Harness To Intake Manifold
    G03827665Courtesy of SUBARU OF AMERICA, INC.
  14. Remove the engine harness from intake manifold.
  15. Remove the bolts which install injector pipe on the intake manifold as shown in Fig 9 (RH side), Fig 10 (LH side) & Fig 11 .
    • RH side
      Fig 9: Removing Bolts Installing Injector Pipe On Intake Manifold - RH Side
      G03827666Courtesy of SUBARU OF AMERICA, INC.
    • LH side
    Fig 10: Removing Bolts Installing Injector Pipe On Intake Manifold - LH Side
    G03827667Courtesy of SUBARU OF AMERICA, INC.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.