2005 Subaru Outback XT, AutomaticFACTORY OEM SERVICE PROCEDURE

Read Current Data For Engine (OBD Mode)

  1. On the << Main Menu>> display screen, select the {Each System Check} and press the [YES] key.
  2. On the << System Selection Menu>> display screen, select the {Engine} and press the [YES] key.
  3. Press the [YES] key after the information of engine type was displayed.
  4. On the << Engine Diagnosis>> display screen, select the {OBD System} and press the [YES] key.
  5. On the << OBD Menu>> screen, select the {Current Data Display/Save}, and then press the [YES] key.
  6. On the << Data Display Menu>> screen, select the {Data Display} and press the [YES] key.
  7. Using the scroll key, move the display screen up or down until the desired data is shown.
  • A list of the support data is shown in READ CURRENT DATA FOR ENGINE (OBD MODE)  .
    READ CURRENT DATA FOR ENGINE (OBD MODE)

    Description Display Unit of measure Note (at idling)
    Number of diagnosis code Number of Diag. Code: - -
    Condition of malfunction indicator light MI (MIL) - ON or OFF
    Monitoring test of misfire Misfire monitoring - complete or incomplete
    Monitoring test of fuel system Fuel system monitoring - complete or incomplete
    Monitoring test of comprehensive component Component monitoring - complete or incomplete
    Test of catalyst Catalyst Diagnosis - complete or incomplete
    Test of heating-type catalyst Heated catalyst - no support
    Test of evaporative emission purge control system Evaporative purge system - complete or incomplete
    Test of secondary air system Secondary air system - no support
    Test of air conditioning system refrigerant A/C system refrigerant - no support
    Test of oxygen sensor Oxygen sensor - complete or incomplete
    Test of oxygen sensor heater O2 Heater Diagnosis - complete or incomplete
    Test of EGR system EGR system - no support
    Air fuel ratio control system for bank 1 Fuel System for Bank 1 - CLOSE normal
    Engine load data Calculated load value % 1.6%
    Engine coolant temperature signal Coolant Temp. °C or °F +91°C or 196°F
    Short term fuel trim by front oxygen (A/F) sensor Short term fuel trim B1 % +0.0%
    Long term fuel trim by front oxygen (A/F) sensor Long term fuel trim B1 % +1.6%
    Intake manifold absolute pressure signal Mani. Absolute Pressure mmHg, kPa, inHg or psig 256 mmHg
    Engine speed signal Engine Speed rpm 693 rpm
    Vehicle speed signal Vehicle Speed km/h or MPH 0 km/h
    Ignition timing advance for #1 cylinder Ignition timing adv. #1 ° +16.0°
    Intake air temperature signal Intake Air Temp. °C or °F 54°C or 129°F
    Intake air amount Mass Air Flow g/s or lb/m 3.1 g/s
    Throttle position signal Throttle Opening Angle % 13%
    Oxygen sensor #12 Oxygen Sensor #12 V +0.800 V
    Air fuel ratio correction by rear oxygen sensor Short term fuel trim #12 % +0.8%
    On-board diagnostic system OBD System - CARB-OBD2
    Oxygen sensor #11 Oxygen Sensor #11 - Support
    Rear oxygen sensor output signal Oxygen Sensor #12 - Support
    A/F sensor output signal A/F sensor #11 - 0.984
    A/F lambda signal A/F sensor #11 V 2.712 V
    A/F lambda signal #11 A/F sensor #11 - 0.992
    A/F sensor current #11 A/F sensor #11 mA -0.03 mA
NOTE: For detailed operation procedure, refer to the " SUBARU SELECT MONITOR OPERATION MANUAL ".
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.