Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Subaru Outback F6-3.0LFACTORY OEM SERVICE PROCEDURE
Subaru Select Monitor
Subaru Select Monitor
OPERATION
1. HOW TO USE SUBARU SELECT MONITOR
1. Prepare the Subaru Select Monitor kit.
2. Connect the diagnosis cable to Subaru Select Monitor.
3. Insert the cartridge to Subaru Select Monitor.
4. Connect the Subaru Select Monitor to data link connector.
1. Data link connector located in the lower portion of the instrument panel (on the driver's side).
2. Connect the diagnosis cable to data link connector.
CAUTION: Do not connect the scan tools except for Subaru Select Monitor and general scan tool.
5. Turn the ignition switch to ON (engine OFF) and turn Subaru Select Monitor switch to ON.
6. Using the Subaru Select Monitor, call up DTC and data, then record them.
2. READ DIAGNOSTIC TROUBLE CODE (DTC) FOR ENGINE (NORMAL MODE)
Refer to "Read Diagnostic Trouble Code (DTC)" for information about how to indicate DTC. Reading Diagnostic Trouble Codes
3. READ DIAGNOSTIC TROUBLE CODE (DTC) FOR ENGINE (OBD MODE)
Refer to "Read Diagnostic Trouble Code (DTC)" for information about how to indicate DTC. Reading Diagnostic Trouble Codes
4. READ CURRENT DATA FOR ENGINE. (NORMAL MODE)
1. On the "Main Menu" display screen, select the {Each System Check} and press the [YES] key.
2. On the "System Selection Menu" display screen, select the {Engine} and press the [YES] key.
3. Press the [YES] key after the information of engine type has been displayed.
4. On the "Engine Diagnosis" display screen, select the {Current Data Display/Save}, and then press the [YES] key.
5. On the "Data Display Menu" display screen, select the {Data Display} and press the [YES] key.
6. Using the scroll key, scroll the display screen up or down until the desired data is shown.
- A list of the support data is shown in the table.
5. READ CURRENT DATA FOR ENGINE (OBD MODE)
1) On the "Main Menu" display screen, select the {Each System Check} and press the [YES] key.
2) On the "System Selection Menu" display screen, select the {Engine} and press the [YES] key.
3) Press the [YES] key after the information of engine type has been displayed.
4) On the "Engine Diagnosis" display screen, select the {OBD system} and press the [YES] key.
5) On the "OBD Menu" display screen, select the {Current Data Display/Save}, and press the [YES] key.
6) On the "Data Display Menu" display screen, select the {Data Display} and press the [YES] key.
7) Using the scroll key, scroll the display screen up or down until the desired data is shown.
- A list of the support data is shown in the table.
6. READ FREEZE FRAME DATA FOR ENGINE (OBD MODE)
1) On the "Main Menu" display screen, select the {Each System Check} and press the [YES] key.
2) On the "System Selection Menu" display screen, select the {Engine} and press the [YES] key.
3) Press the [YES] key after the information of engine type has been displayed.
4) On the "Engine Diagnosis" display screen, select the {OBD System} and press the [YES] key.
5) On the "OBD Menu" display screen, select the {Freeze Frame Data} and press the [YES] key.
- A list of the support data is shown in the table.
7. LED OPERATION MODE FOR ENGINE
1) On the "Main Menu" display screen, select the {Each System Check} and press the [YES] key.
2) On the "System Selection Menu" display screen, select the {Engine} and press the [YES] key.
3) Press the [YES] key after the information of engine type has been displayed.
4) On the "Engine Diagnosis" display screen, select the {Current Data Display/Save}, and then press the [YES] key.
5) On the "Data Display Menu" display screen, select the {Data & LED Display} and press the [YES] key.
6) Using the scroll key, scroll the display screen up or down until the desired data is shown.
- A list of the support data is shown in the table.
8. VIN REGISTRATION
1. On the "Main Menu" display screen, select the {Each System Check} and press the [YES] key.
2. On the "System Selection Menu" display screen, select the {Engine} and press the [YES] key.
3. Press the [YES] key after the information of engine type has been displayed.
4. On the "Engine Diagnosis" display screen, select the {VIN Registration} and press the [YES] key.
5. Perform the procedure shown on display screen.
NOTE: For detailed operation procedures, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.
OPERATION
1. HOW TO USE SUBARU SELECT MONITOR
1. Prepare the Subaru Select Monitor kit.
2. Connect the diagnosis cable to Subaru Select Monitor.
3. Insert the cartridge to Subaru Select Monitor.
4. Connect the Subaru Select Monitor to data link connector.
1. Data link connector located in the lower portion of the instrument panel (on the driver's side).
2. Connect the diagnosis cable to data link connector.
CAUTION: Do not connect the scan tools except for Subaru Select Monitor and general scan tool.
5. Turn the ignition switch to ON (engine OFF) and turn Subaru Select Monitor switch to ON.
6. Using the Subaru Select Monitor, call up DTC and data, then record them.
2. READ DIAGNOSTIC TROUBLE CODE (DTC) FOR ENGINE (NORMAL MODE)
Refer to "Read Diagnostic Trouble Code (DTC)" for information about how to indicate DTC. Reading Diagnostic Trouble Codes
3. READ DIAGNOSTIC TROUBLE CODE (DTC) FOR ENGINE (OBD MODE)
Refer to "Read Diagnostic Trouble Code (DTC)" for information about how to indicate DTC. Reading Diagnostic Trouble Codes
4. READ CURRENT DATA FOR ENGINE. (NORMAL MODE)
1. On the "Main Menu" display screen, select the {Each System Check} and press the [YES] key.
2. On the "System Selection Menu" display screen, select the {Engine} and press the [YES] key.
3. Press the [YES] key after the information of engine type has been displayed.
4. On the "Engine Diagnosis" display screen, select the {Current Data Display/Save}, and then press the [YES] key.
5. On the "Data Display Menu" display screen, select the {Data Display} and press the [YES] key.
6. Using the scroll key, scroll the display screen up or down until the desired data is shown.
Part 1:
Part 2:
Part 3:
- A list of the support data is shown in the table.
5. READ CURRENT DATA FOR ENGINE (OBD MODE)
1) On the "Main Menu" display screen, select the {Each System Check} and press the [YES] key.
2) On the "System Selection Menu" display screen, select the {Engine} and press the [YES] key.
3) Press the [YES] key after the information of engine type has been displayed.
4) On the "Engine Diagnosis" display screen, select the {OBD system} and press the [YES] key.
5) On the "OBD Menu" display screen, select the {Current Data Display/Save}, and press the [YES] key.
6) On the "Data Display Menu" display screen, select the {Data Display} and press the [YES] key.
7) Using the scroll key, scroll the display screen up or down until the desired data is shown.
Part 1:
Part 2:
- A list of the support data is shown in the table.
6. READ FREEZE FRAME DATA FOR ENGINE (OBD MODE)
1) On the "Main Menu" display screen, select the {Each System Check} and press the [YES] key.
2) On the "System Selection Menu" display screen, select the {Engine} and press the [YES] key.
3) Press the [YES] key after the information of engine type has been displayed.
4) On the "Engine Diagnosis" display screen, select the {OBD System} and press the [YES] key.
5) On the "OBD Menu" display screen, select the {Freeze Frame Data} and press the [YES] key.
- A list of the support data is shown in the table.
7. LED OPERATION MODE FOR ENGINE
1) On the "Main Menu" display screen, select the {Each System Check} and press the [YES] key.
2) On the "System Selection Menu" display screen, select the {Engine} and press the [YES] key.
3) Press the [YES] key after the information of engine type has been displayed.
4) On the "Engine Diagnosis" display screen, select the {Current Data Display/Save}, and then press the [YES] key.
5) On the "Data Display Menu" display screen, select the {Data & LED Display} and press the [YES] key.
6) Using the scroll key, scroll the display screen up or down until the desired data is shown.
- A list of the support data is shown in the table.
8. VIN REGISTRATION
1. On the "Main Menu" display screen, select the {Each System Check} and press the [YES] key.
2. On the "System Selection Menu" display screen, select the {Engine} and press the [YES] key.
3. Press the [YES] key after the information of engine type has been displayed.
4. On the "Engine Diagnosis" display screen, select the {VIN Registration} and press the [YES] key.
5. Perform the procedure shown on display screen.
NOTE: For detailed operation procedures, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.