Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Subaru Outback F6-3.0LFACTORY OEM SERVICE PROCEDURE
Actuator Operation
Compulsory Valve Operation Check Mode
OPERATION
1. Prepare the Subaru Select Monitor kit.
2. Connect the diagnosis cable to Subaru Select Monitor.
3. Insert the cartridge to Subaru Select Monitor.
4. Connect the test mode connector (A. located at the lower portion of glove box.
5. Connect the Subaru Select Monitor to data link connector located in the lower portion of the instrument panel (on the driver's side.)
CAUTION: Do not connect the scan tools except for Subaru Select Monitor or general scan tool.
6. Turn the ignition switch to ON (engine OFF. and turn on the Subaru Select Monitor switch.
7. On the "Main Menu" display screen, select the {Each System Check} and press the [YES] key.
8. On the "System Selection Menu" display screen, select the {Engine} and press the [YES] key.
9. Press the [YES] key after the information of engine type was displayed.
10. On the "Engine Diagnosis" display screen, select the {System Operation Check Mode} and press the [YES] key.
11. On the "System Operation Check Mode" display screen, select the {Actuator ON/OFF Operation} and press the [YES] key.
12. Select the desired actuator on the "Actuator ON/OFF Operation" display screen and press the [YES] key.
13. Pressing the [NO] key completes the compulsory valve operation check mode. The display will then return to the "Actuator ON/OFF Operation"
- A list of the support data is shown in the table.
NOTE:
- The parts will be displayed but not functional.
- For detailed operation procedures, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.
OPERATION
1. Prepare the Subaru Select Monitor kit.
2. Connect the diagnosis cable to Subaru Select Monitor.
3. Insert the cartridge to Subaru Select Monitor.
4. Connect the test mode connector (A. located at the lower portion of glove box.
5. Connect the Subaru Select Monitor to data link connector located in the lower portion of the instrument panel (on the driver's side.)
CAUTION: Do not connect the scan tools except for Subaru Select Monitor or general scan tool.
6. Turn the ignition switch to ON (engine OFF. and turn on the Subaru Select Monitor switch.
7. On the "Main Menu" display screen, select the {Each System Check} and press the [YES] key.
8. On the "System Selection Menu" display screen, select the {Engine} and press the [YES] key.
9. Press the [YES] key after the information of engine type was displayed.
10. On the "Engine Diagnosis" display screen, select the {System Operation Check Mode} and press the [YES] key.
11. On the "System Operation Check Mode" display screen, select the {Actuator ON/OFF Operation} and press the [YES] key.
12. Select the desired actuator on the "Actuator ON/OFF Operation" display screen and press the [YES] key.
13. Pressing the [NO] key completes the compulsory valve operation check mode. The display will then return to the "Actuator ON/OFF Operation"
- A list of the support data is shown in the table.
NOTE:
- The parts will be displayed but not functional.
- For detailed operation procedures, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.