Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Subaru Baja Base, AutomaticFACTORY OEM SERVICE PROCEDURE
Read Current Data For At.
- On the << Main Menu >> display screen, select the {Each System Check} and press the [YES] key.
- On the << System Selection Menu >> display screen, select the {Transmission Control System} and press the [YES] key.
- Press the [YES] key after displayed the information of transmission type.
- On the << Transmission Diagnosis >> display screen, select the {Current Data Display & Save} and press the [YES] key.
- On the << Data Display Menu >> display screen, select the {Data Display} and press the [YES] key.
- Using the scroll key, move the display screen up or down until the desired data is shown.
- A list of the support data is shown in the following table.SUPPORT DATA LIST (AT CURRENT DATA)
Contents Display Unit of measure Battery voltage Battery Voltage V Rear vehicle speed sensor signal Vehicle Speed #1 km/h or MPH Front vehicle speed sensor signal Vehicle Speed #2 km/h or MPH Engine speed signal Engine Speed RPM Automatic transmission fluid temperature signal ATF Temp. °C or °F Throttle position signal Throttle Sensor Voltage V Gear position Gear Position - Line pressure control duty ratio Line Pressure Duty Ratio % Lock up clutch control duty ratio Lock Up Duty Ratio % Transfer clutch control duty ratio Transfer Duty Ratio % Power supply for throttle position sensor Throttle Sensor Power V Torque converter turbine speed signal AT Turbine Speed RPM 2-4 brake timing pressure control duty ratio 2-4B Duty Ratio % Intake manifold pressure sensor voltage Mani. Pressure Voltage V 2 wheel drive switch signal 2WD Switch ON or OFF Stop lamp switch signal Stop Lamp Switch ON or OFF Anti lock brake system signal ABS Signal ON or OFF Cruise control system signal Cruise Control Signal ON or OFF Neutral/Parking range signal N/P Range Signal ON or OFF Reverse range signal R Range Signal ON or OFF Drive range signal D Range Signal ON or OFF 3rd range signal 3rd Range Signal ON or OFF 2nd range signal 2nd Range Signal ON or OFF 1st range signal 1st Range Signal ON or OFF Shift control solenoid A Shift Solenoid #1 ON or OFF Shift control solenoid B Shift Solenoid #2 ON or OFF Torque control output signal #1 Torque Control Signal #1 ON or OFF Torque control output signal #2 Torque Control Signal #2 ON or OFF Torque control cut signal Torque Control Cut Sig. ON or OFF 2-4 brake timing control solenoid valve 2-4 Brake Timing Sol. ON or OFF Low clutch timing control solenoid valve Low Clutch Timing Sol. ON or OFF Automatic transmission diagnosis indicator lamp AT Diagnosis Lamp ON or OFF
NOTE: For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL. For select monitor display details, refer to the following. - A list of the support data is shown in the following table.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.