Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2003 Subaru Outback F6-3.0LFACTORY OEM SERVICE PROCEDURE
Clutch Switch: Service and Repair
CLUTCH SWITCH
REMOVAL
1. Disconnect the ground cable from battery.
2. Remove the instrument panel lower cover.
3. Disconnect the connector from clutch switch.
4. Remove the clutch switch.
INSTALLATION
CLUTCH SWITCH (WITH CRUISE CONTROL)

1. Install the clutch switch and clutch pedal stopper so that the gap between them is O mm (O inch).
Tightening torque: 8 Nm (0.8 kgf-m, 5.8 ft. lbs.)

2. Measure stroke of clutch pedal.
Specified clutch pedal full stroke: A 130 - 135 mm (5.12 - 5.31 inch)
3. If the clutch pedal stroke is out of specification, adjust the stroke.
4. Connect clutch switch connector.
CLUTCH SWITCH (STARTER INTERLOCK)
1. Fully depress the clutch pedal.

2. Install the clutch pedal plate and clutch pedal so that the gap between them is 3 - 3.5 mm (0.12 - 0.14 inch), and then tighten the lock nut.
Tightening torque: 8 Nm (0.8 kgf-m, 13.0 ft. lbs.)
3. Connect the clutch switch connector.
4. Confirm that the engine does not start when the clutch pedal is released.
5. Confirm that the engine starts when the clutch pedal is fully depressed.
INSPECTION
1. Confirm that the engine does not start when the clutch pedal is released. If the engine starts, adjust the clutch switch and inspect the starter interlock circuit.
2. Confirm that the engine starts when the clutch pedal is fully depressed. If the engine does not start, adjust the clutch switch and inspect the starter interlock circuit.
3. Check the clutch switch continuity. If continuity is not as specified, replace the switch.
1. Disconnect the clutch switch connector.
2. Measure the resistance between 1 and 2 of switch terminal.
Terminals/Specified resistance
When clutch pedal depressed: 1-2/Less than 1 Q
Terminals/Specified resistance
When clutch pedal not depressed: 1-2/More than 1 M Q

Clutch switch (Starter interlock)

Clutch switch (With cruise control)
ADJUSTMENT

1. Loosen the clutch switch mounting lock nut (Starter interlock).
2. Fully depress the clutch pedal.

3. Adjust the clutch pedal plate and clutch switch so that the gap between them is 3 - 3.5 mm (0.12 - 0.14 inch).
4. Tighten the lock nut.
Tightening torque (Clutch stopper nut): 8 Nm (0.8 kgf-m, 13.0 ft. lbs.)
REMOVAL
1. Disconnect the ground cable from battery.
2. Remove the instrument panel lower cover.
3. Disconnect the connector from clutch switch.
4. Remove the clutch switch.
INSTALLATION
CLUTCH SWITCH (WITH CRUISE CONTROL)
1. Install the clutch switch and clutch pedal stopper so that the gap between them is O mm (O inch).
Tightening torque: 8 Nm (0.8 kgf-m, 5.8 ft. lbs.)
2. Measure stroke of clutch pedal.
Specified clutch pedal full stroke: A 130 - 135 mm (5.12 - 5.31 inch)
3. If the clutch pedal stroke is out of specification, adjust the stroke.
4. Connect clutch switch connector.
CLUTCH SWITCH (STARTER INTERLOCK)
1. Fully depress the clutch pedal.
2. Install the clutch pedal plate and clutch pedal so that the gap between them is 3 - 3.5 mm (0.12 - 0.14 inch), and then tighten the lock nut.
Tightening torque: 8 Nm (0.8 kgf-m, 13.0 ft. lbs.)
3. Connect the clutch switch connector.
4. Confirm that the engine does not start when the clutch pedal is released.
5. Confirm that the engine starts when the clutch pedal is fully depressed.
INSPECTION
1. Confirm that the engine does not start when the clutch pedal is released. If the engine starts, adjust the clutch switch and inspect the starter interlock circuit.
2. Confirm that the engine starts when the clutch pedal is fully depressed. If the engine does not start, adjust the clutch switch and inspect the starter interlock circuit.
3. Check the clutch switch continuity. If continuity is not as specified, replace the switch.
1. Disconnect the clutch switch connector.
2. Measure the resistance between 1 and 2 of switch terminal.
Terminals/Specified resistance
When clutch pedal depressed: 1-2/Less than 1 Q
Terminals/Specified resistance
When clutch pedal not depressed: 1-2/More than 1 M Q
Clutch switch (Starter interlock)
Clutch switch (With cruise control)
ADJUSTMENT
1. Loosen the clutch switch mounting lock nut (Starter interlock).
2. Fully depress the clutch pedal.
3. Adjust the clutch pedal plate and clutch switch so that the gap between them is 3 - 3.5 mm (0.12 - 0.14 inch).
4. Tighten the lock nut.
Tightening torque (Clutch stopper nut): 8 Nm (0.8 kgf-m, 13.0 ft. lbs.)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
