Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2003 Subaru Forester F4-2.5L SOHCFACTORY OEM SERVICE PROCEDURE
Throttle Position Sensor: Adjustments
ADJUSTMENT
1. Turn the ignition switch to OFF.

2. Loosen the throttle position sensor holding screws.
3. When using voltage meter;
1. Take out the ECM.
2. Turn the ignition switch to ON.

3. Adjust the throttle position sensor to the proper position to allow the voltage signal to the ECM to be in specification.
Connector & terminal/Specified voltage
(B134) No. 3 (+) - (B134) No. 13 (-) / 0.45 - 0.55 V
[Fully closed.]

4. Tighten the throttle position sensor holding screws.
Tightening torque: 1.6 N.m (0.16 kgf.m, 1.2 ft.lb)
4. When using Subaru Select Monitor;
1. Turn the ignition switch to OFF.

2. Loosen the throttle position sensor holding screws.
NOTE: For detailed operation procedures, refer to the Subaru Select Monitor Operation Manual.

3. Insert the cartridge to the Subaru Select Monitor.

4. Connect the Subaru Select Monitor to the data link connector.
5. Turn the ignition switch to ON, and the Subaru Select Monitor switch to ON.
6. Select the {2. Each System Check} in Main Menu.
7. Select the {Engine Control System} in Selection Menu.
8. Select the {1. Current Data Display & Save} in Engine Control System Diagnosis.
9. Select the {1.12 Data Display} in Data Display Menu.
10. Adjust the throttle position sensor to the proper position to match with the following specifications.
Condition: Throttle fully closed
Throttle opening angle 0.00 %
Throttle sensor voltage 0.50 V

11. Tighten the throttle position sensor holding screws.
Tightening torque: 1.6 N.m (0.16 kgf.m, 1.2 ft.lb)
1. Turn the ignition switch to OFF.
2. Loosen the throttle position sensor holding screws.
3. When using voltage meter;
1. Take out the ECM.
2. Turn the ignition switch to ON.
3. Adjust the throttle position sensor to the proper position to allow the voltage signal to the ECM to be in specification.
Connector & terminal/Specified voltage
(B134) No. 3 (+) - (B134) No. 13 (-) / 0.45 - 0.55 V
[Fully closed.]
4. Tighten the throttle position sensor holding screws.
Tightening torque: 1.6 N.m (0.16 kgf.m, 1.2 ft.lb)
4. When using Subaru Select Monitor;
1. Turn the ignition switch to OFF.
2. Loosen the throttle position sensor holding screws.
NOTE: For detailed operation procedures, refer to the Subaru Select Monitor Operation Manual.
3. Insert the cartridge to the Subaru Select Monitor.
4. Connect the Subaru Select Monitor to the data link connector.
5. Turn the ignition switch to ON, and the Subaru Select Monitor switch to ON.
6. Select the {2. Each System Check} in Main Menu.
7. Select the {Engine Control System} in Selection Menu.
8. Select the {1. Current Data Display & Save} in Engine Control System Diagnosis.
9. Select the {1.12 Data Display} in Data Display Menu.
10. Adjust the throttle position sensor to the proper position to match with the following specifications.
Condition: Throttle fully closed
Throttle opening angle 0.00 %
Throttle sensor voltage 0.50 V
11. Tighten the throttle position sensor holding screws.
Tightening torque: 1.6 N.m (0.16 kgf.m, 1.2 ft.lb)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
