Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2002 Subaru Outback L.L.Bean Edition AWD F6-3.0LFACTORY OEM SERVICE PROCEDURE
Engine Oil: Service and Repair
REPLACEMENT
When refilling engine oil, replace oil filter at the same time.

1) Drain engine oil by loosening engine oil drain plug.

2) Open engine oil filler cap for quick draining of the engine oil.
3) Replace drain plug gasket.

4) Tighten engine oil drain plug after draining engine oil.
Tightening torque: 44 Nm (4.5 kgf-m, 33 ft. lbs.)
5) Fill engine oil through filler pipe up to upper point on level gauge. Make sure that vehicle is placed level when checking oil level. Use engine oil of proper quality and viscosity, selected in accordance with the table in figure.

Recommended oil
API classification SL or SJ with the words "Energy Conserving or Energy conserving II", CCMC specification G4 or G5, ACEA specification A1, A2 or A3, or New API mark displayed on the container (if it is impossible to get SL or SJ, grade, you may use SG grade.)
Engine oil amount for refill: 5.8 L (6.1 US qt., 5.1 Imp qt.)
The proper viscosity helps vehicle get good cold and hot starting by reducing viscous friction and thus increasing cranking speed.
CAUTION: When replenishing oil, it does not matter if the oil to be added is a different brand from that in the engine; however, use oil having the API classification and SAE viscosity No. designated by SUBARU.
NOTE: If vehicle is used in desert areas with very high temperatures or for other heavy duty applications, the following viscosity oils may be used:
API classification: SL or SJ
SAE Viscosity No.: 30, 40, 10W-50, 20W-40, 20W50.
6) Close engine oil filler cap.
7) Start engine and warm it up for a time.

8) After engine stops, recheck the oil level. If necessary, add engine oil up to upper level on level gauge.
When refilling engine oil, replace oil filter at the same time.
1) Drain engine oil by loosening engine oil drain plug.
2) Open engine oil filler cap for quick draining of the engine oil.
3) Replace drain plug gasket.
4) Tighten engine oil drain plug after draining engine oil.
Tightening torque: 44 Nm (4.5 kgf-m, 33 ft. lbs.)
5) Fill engine oil through filler pipe up to upper point on level gauge. Make sure that vehicle is placed level when checking oil level. Use engine oil of proper quality and viscosity, selected in accordance with the table in figure.
Recommended oil
API classification SL or SJ with the words "Energy Conserving or Energy conserving II", CCMC specification G4 or G5, ACEA specification A1, A2 or A3, or New API mark displayed on the container (if it is impossible to get SL or SJ, grade, you may use SG grade.)
Engine oil amount for refill: 5.8 L (6.1 US qt., 5.1 Imp qt.)
The proper viscosity helps vehicle get good cold and hot starting by reducing viscous friction and thus increasing cranking speed.
CAUTION: When replenishing oil, it does not matter if the oil to be added is a different brand from that in the engine; however, use oil having the API classification and SAE viscosity No. designated by SUBARU.
NOTE: If vehicle is used in desert areas with very high temperatures or for other heavy duty applications, the following viscosity oils may be used:
API classification: SL or SJ
SAE Viscosity No.: 30, 40, 10W-50, 20W-40, 20W50.
6) Close engine oil filler cap.
7) Start engine and warm it up for a time.
8) After engine stops, recheck the oil level. If necessary, add engine oil up to upper level on level gauge.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
