2002 Subaru Outback L.L. Bean EditionFACTORY OEM SERVICE PROCEDURE

Draining Fuel

WARNING:
  • Place "NO FIRE" signs near the working area.
  • Be careful not to spill fuel on the floor.
  1. Set vehicle on the lift.
  2. Disconnect battery ground cable.
    Fig 1: Disconnecting Battery Ground Cable
    G03584285Courtesy of SUBARU OF AMERICA, INC.
  3. Lift-up the vehicle.
  4. Remove front right side fuel tank cover.
    Fig 2: Removing Front Right Side Fuel Tank Cover
    G03584286Courtesy of SUBARU OF AMERICA, INC.
  5. Drain fuel from fuel tank.

    Set a container under the vehicle and remove drain plug from fuel tank.

    Fig 3: Removing Drain Plug From Fuel Tank
    G03584287Courtesy of SUBARU OF AMERICA, INC.
  6. Tighten fuel drain plug and install front right side tank cover.

    Tightening torque: 

    26 N.m (2.65 kgf-m, 19.2 ft-lb) 

    Fig 4: Tightening Fuel Drain Plug Bolt (1 Of 2)
    G03584288Courtesy of SUBARU OF AMERICA, INC.

    Tightening torque: 

    18 N.m (1.8 kgf-m, 13.0 ft-lb) 

    Fig 5: Tightening Fuel Drain Plug Bolt (2 Of 2)
    G03584289Courtesy of SUBARU OF AMERICA, INC.
  7. Lower the vehicle.
  8. Remove sub service hole cover.
    Fig 6: Removing Sub Service Hole Cover
    G03584290Courtesy of SUBARU OF AMERICA, INC.
  9. Disconnect connector from fuel sub level sensor.
    Fig 7: Disconnecting Connector From Fuel Sub Level Sensor
    G03584291Courtesy of SUBARU OF AMERICA, INC.
  10. Disconnect fuel jet pump hose.
    Fig 8: Disconnecting Fuel Jet Pump Hose
    G03584292Courtesy of SUBARU OF AMERICA, INC.
  11. Remove fuel sub level sensor.
    Fig 9: Removing Fuel Sub Level Sensor
    G03584293Courtesy of SUBARU OF AMERICA, INC.
  12. Drain fuel from fuel tank by using hand pump.
    WARNING: Do not use a motor pump when draining fuel.
  13. After draining fuel, reinstall fuel sub level sensor.

    Tightening torque: 

    T: 4.4 N.m (0.45 kgf-m, 3.3 ft-lb) 

    Fig 10: Installing Fuel Sub Level Sensor
    G03584294Courtesy of SUBARU OF AMERICA, INC.
NOTE: If you have not removed fuel tank yet, proceed with the procedure below for installation.
  1. Connect fuel jet pump hose.
    Fig 11: Connecting Fuel Jet Pump Hose
    G03584295Courtesy of SUBARU OF AMERICA, INC.
  2. Connect connector from fuel sub level sensor.
    Fig 12: Connecting Connector From Fuel Sub Level Sensor
    G03584296Courtesy of SUBARU OF AMERICA, INC.
  3. Install sub service hole cover.
    Fig 13: Installing Sub Service Hole Cover
    G03584297Courtesy of SUBARU OF AMERICA, INC.
  4. Set rear seat and floor mat.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.