Wheel Alignment Specifications

2000 Subaru Forester L, AutomaticSECTION Wheel Alignment Specifications
WHEEL ALIGNMENT SPECIFICATIONS

Application Preferred Range
Forester
Camber (1)
Front -0.25 -0.75 To 0.25
Rear -0.25 -1.0 To 0.17
Caster (1) 2.83 2.08 To 3.58
Toe-In (2)
Front 0 (0) -0.12 To 0.12 (-3 To 3)
Rear -0.1 (-2.5) -0.16 To 0.04 (-4 To -1)
Toe-In (1)
Front 0 -0.24 To 0.24
Rear -0.2 -0.32 To 0.08
Impreza 2.2L
Camber (1)
Front 0 -0.5 To 0.5
Rear -0.92 -1.0 To -0.17
Caster (1) 3 2 To 4
Toe-In (2)
Front 0 (0) -0.12 To 0.12 (-3 To 3)
Rear 0 (0) -0.12 To 0.12 (-3 To 3)
Toe-In (1)
Front 0 -0.24 To 0.24
Rear 0 -0.24 To 0.24
Impreza 2.5L
Camber (1)
Front -0.42 -0.92 To 0.08
Rear -1.17 -1.92 To -0.42
Caster (1) 3.08 2.08 To 4.08
Toe-In (2)
Front 0 (0) -0.12 To 0.12 (-3 To 3)
Rear 0 (0) -0.12 To 0.12 (-3 To 3)
Toe-In (1)
Front 0 -0.24 To 0.24
Rear 0 -0.24 To 0.24
Legacy Sedan
Camber (1)
Front -0.08 -0.58 To 0.42
Rear -0.5 -1.25 To 0.25
Caster (1) 3.08 2.33 To 3.83
Toe-In (2)
Front 0 (0) -0.12 To 0.12 (-3 To 3)
Rear 0 (0) -0.12 To 0.12 (-3 To 3)
Toe-In (1)
Front 0 -0.33 To 0.33
Rear 0 -0.33 To 0.33
Legacy Wagon
Camber (1)
Front -0.08 -0.58 To 0.42
Rear -0.33 -1.08 To 0.42
Caster (1) 2.83 2.08 To 3.58
Toe-In (2)
Front 0 (0) -0.12 To 0.12 (-3 To 3)
Rear 0 (0) -0.12 To 0.12 (-3 To 3)
Toe-In (1)
Front 0 -0.33 To 0.33
Rear 0 -0.33 To 0.33
Legacy Outback
Camber (1)
Front 0.33 -0.17 To 0.83
Rear -0.17 -0.92 To 0.58
Caster (1) 2.67 1.92 To 3.42
Toe-In (2)
Front 0 (0) -0.12 To 0.12 (-3 To 3)
Rear 0 (0) -0.12 To 0.12 (-3 To 3)
Toe-In (1)
Front 0 -0.33 To 0.33
Rear 0 -0.33 To 0.33
(1) Measurement is in degrees.
(2) Measurement is in inches (millimeters).
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.