1992 Subaru Legacy LEFACTORY OEM SERVICE PROCEDURE

Wheel Alignment Specifications

WHEEL ALIGNMENT SPECIFICATIONS (JUSTY)

Application Preferred Range
Camber (1)
Front 0.67 -0.33 To 1.67
Rear 0 -1 To 1
Caster (1) 2.5 1.5 To 3.5
Toe-In (2)
Front 0.08 (2) 0.04 To 0.12 (1 To 3)
Rear 0 (0) -0.12 To 0.12 (-3 To 3)
Toe-In (1)
Front 0.2 0.1 To 0.3
Rear 0 -0.3 To 0.3
(1) Measurement is in degrees.
(2) Measurement is in inches (mm).
WHEEL ALIGNMENT SPECIFICATIONS (LEGACY SEDAN - 2WD)

Application Preferred Range
Camber (1)
Front -0.25 -0.75 To 0.25
Rear -1 -2 To 0
Caster (1) 3.08 2.08 To 4.08
Toe-In (2)
Front 0 (0) -0.12 To 0.12 (-3 To 3)
Rear 0 (0) -0.12 To 0.12 (-3 To 3)
Toe-In (1)
Front 0 -0.3 To 0.3
Rear 0 -0.3 To 0.3
(1) Measurement is in degrees.
(2) Measurement is in inches (mm).
WHEEL ALIGNMENT SPECIFICATIONS (LEGACY SEDAN - 4WD)

Application Preferred Range
Camber (1)
Front 0 -0.5 To 0.5
Rear -1 -2 To 0
Caster (1) 3 2 To 4
Toe-In (2)
Front 0 (0) -0.12 To 0.12 (-3 To 3)
Rear 0 (0) -0.12 To 0.12 (-3 To 3)
Toe-In (1)
Front 0 -0.3 To 0.3
Rear 0 -0.3 To 0.3
(1) Measurement is in degrees.
(2) Measurement is in inches (mm).
WHEEL ALIGNMENT SPECIFICATIONS (LEGACY WAGON - 2WD)

Application Preferred Range
Camber (1)
Front -0.25 -0.75 To 0.25
Rear -0.83 -1.83 To 0.17
Caster (1) 2.83 1.83 To 3.83
Toe-In (2)
Front 0 (0) -0.12 To 0.12 (-3 To 3)
Rear 0 (0) -0.12 To 0.12 (-3 To 3)
Toe-In (1)
Front 0 -0.3 To 0.3
Rear 0 -0.3 To 0.3
(1) Measurement is in degrees.
(2) Measurement is in inches (mm).
WHEEL ALIGNMENT SPECIFICATIONS (LEGACY WAGON - 4WD)

Application Preferred Range
Camber (1)
Front 0 -0.5 To 0.5
Rear -0.83 -1.83 To 0.17
Caster (1) 2.75 1.75 To 3.75
Toe-In (2)
Front 0 (0) -0.12 To 0.12 (-3 To 3)
Rear 0 (0) -0.12 To 0.12 (-3 To 3)
Toe-In (1)
Front 0 -0.3 To 0.3
Rear 0 -0.3 To 0.3
(1) Measurement is in degrees.
(2) Measurement is in inches (mm).
WHEEL ALIGNMENT SPECIFICATIONS (LOYALE SEDAN - 2WD)

Application Preferred Range
Camber (1)
Front 0.75 0 To 1.5
Rear 0 -0.5 To 0.5
Caster (1) 2.5 1.75 To 3.25
Toe-In (2)
Front 0.08 (2) 0.04 To 0.12 (1 To 3)
Rear 0 (0) -0.08 To 0.08 (-2 To 2)
Toe-In (1)
Front 0.2 0.1 To 0.3
Rear 0 -0.2 To 0.2
(1) Measurement is in degrees.
(2) Measurement is in inches (mm).
WHEEL ALIGNMENT SPECIFICATIONS (LOYALE WAGON - 2WD)

Application Preferred Range
Camber (1)
Front 1 0.25 To 1.75
Rear 0 -0.5 To 0.5
Caster (1) 2.08 1.33 To 2.83
Toe-In (2)
Front 0.08 (2) 0.04 To 0.12 (1 To 3)
Rear 0 (0) -0.08 To 0.08 (-2 To 2)
Toe-In (1)
Front 0.2 0.1 To 0.3
Rear 0 -0.2 To 0.2
(1) Measurement is in degrees.
(2) Measurement is in inches (mm).
WHEEL ALIGNMENT SPECIFICATIONS (LOYALE - 4WD)

Application Preferred Range
Camber (1)
Front 1.67 0.92 To 2.42
Rear 0 -0.5 To 0.5
Caster (1) N/A N/A
Toe-In (2)
Front -0.2 (-5) -0.24 To -0.16 (-6 To -4)
Rear 0 (0) -0.08 To 0.08 (-2 To 2)
Toe-In (1)
Front -0.5 -0.6 To -0.4
Rear 0 -0.2 To 0.2
(1) Measurement is in degrees.
(2) Measurement is in inches (mm).
WHEEL ALIGNMENT SPECIFICATIONS (SVX)

Application Preferred Range
Camber (1)
Front -0.42 -1.17 To 0.33
Rear -0.67 -1.42 To 0.08
Caster (1) 4.83 4.08 To 5.58
Toe-In (2)
Front 0 (0) -0.12 To 0.12 (-3 To 3)
Rear 0 (0) -0.12 To 0.12 (-3 To 3)
Toe-In (1)
Front 0 -0.24 To 0.24
Rear 0 -0.24 To 0.24
(1) Measurement is in degrees.
(2) Measurement is in inches (mm).
Chapter Navigation
Return to Chapter: Wheel Alignment Specifications & Procedures
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.