Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2012 Scion xB Automatic TransFACTORY OEM SERVICE PROCEDURE
Differential Case: Disassembly: Disassembly
- REMOVE FRONT DIFFERENTIAL RING GEAR
- Place matchmarks on the ring gear and differential case.
- Remove the 10 bolts.
- Using a plastic-faced hammer, tap on the ring gear to remove it from the case.
- REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING
- SST: 09950-40011
- 09951-04020
- 09952-04010
- 09953-04020
- 09954-04010
- 09955-04061
- 09957-04010
- 09958-04011
- SST: 09950-60010
- 09951-00340
- SST: 09387-00041
- 09387-01030
- 09387-01041
- SST: 09387-02010
- SST: 09387-02020
- Using SST, remove the front differential case tapered roller bearing front inner race from the differential case.Fig 4: Removing Front Differential Case Tapered Roller Bearing Front Inner Race From Differential Case
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
- SST: 09950-40011
- 09951-04020
- 09952-04010
- 09953-04020
- 09954-04010
- 09955-04061
- 09957-04010
- 09958-04011
- SST: 09950-60010
- 09951-00340
- SST: 09950-40011
- Using SST, remove the front differential case tapered roller bearing front outer race and differential case washer.
- SST: 09387-00041
- 09387-01030
- 09387-02010
- 09387-02020
- SST: 09387-00041
- SST: 09950-40011
- REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING
- SST: 09950-40011
- 09951-04020
- 09952-04010
- 09953-04020
- 09954-04010
- 09955-04061
- 09957-04010
- 09958-04011
- SST: 09950-60010
- 09951-00340
- SST: 09387-00041
- 09387-01030
- 09387-01041
- SST: 09387-02010
- SST: 09387-02020
- Using SST, remove the front differential case tapered roller bearing rear inner race from the differential case.Fig 6: Removing Front Differential Case Tapered Roller Bearing Rear Inner Race From Differential Case
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
- SST: 09950-40011
- 09951-04020
- 09952-04010
- 09953-04020
- 09954-04010
- 09955-04061
- 09957-04010
- 09958-04011
- SST: 09950-60010
- 09951-00340
- SST: 09950-40011
- Using SST, remove the front differential case tapered roller bearing rear outer race from the differential case washer.
- SST: 09387-00041
- 09387-01030
- 09387-02010
- 09387-02020
- SST: 09387-00041
- SST: 09950-40011
- REMOVE FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN
- Using a punch and hammer, loosen the staked part of the differential case.
- Using a pin punch (5 mm), tap the pin out from the ring gear side.
- REMOVE NO. 1 FRONT DIFFERENTIAL PINION SHAFT
- Remove the front differential pinion shaft from the differential case.
- REMOVE FRONT DIFFERENTIAL SIDE GEAR
- Remove the 2 front differential pinions, 2 pinion thrust washers, 2 front differential side gears and 2 side gear thrust washers from the differential case.
- REMOVE DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL
- Place the transaxle case in a vise.
- Using SST, remove the oil seal.
- SST: 09308-00010
- REMOVE TRANSAXLE HOUSING OIL SEAL
- Place the transaxle housing in a vise.
- Using SST, remove the oil seal.
- SST: 09308-00010
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
