2012 Scion xB Automatic TransFACTORY OEM SERVICE PROCEDURE

Automatic Transaxle Unit: Inspection: Inspection

  1. INSPECT AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY 
    1. Remove the magnets and use them to collect any steel chips. Examine the clips and particles in the pan and on the magnet to determine what type of wear has occurred in the transaxle.
      Fig 1: Checking Chips And Particles In Pan
      GTY100313Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Steel (magnetic): bearing, gear and plate wear

      Brass (non-magnetic): bush wear

  2. INSPECT INPUT SHAFT END PLAY 
    1. Fix the transaxle case with the oil pump side facing up.
    2. Using a dial indicator, measure the input shaft end play.
      Fig 2: Measuring Input Shaft End Play
      GTY164997Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard end play

      0.26 to 1.25 mm (0.0103 to 0.0492 in.)

  3. INSPECT NO. 2 UNDERDRIVE CLUTCH DISC 

    Check to see if the sliding surface of the disc, plate and flange are worn or burnt.

    Fig 3: Identifying No. 2 Underdrive Clutch Disc
    GTY164646Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    If necessary, replace them.

    NOTE:
    • If the lining of the disc is peeling off or discolored, or if even a part of the groove is defaced, replace all the discs.
    • Before assembling new discs, soak them in ATF for at least 15 minutes.
  4. INSPECT UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY 
    1. Using a vernier caliper, measure the free length of the underdrive brake return spring together with the spring seat.
      Fig 4: Measuring Free Length Of Underdrive Brake Return Spring
      GTY157825Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard free length

      14.04 mm (0.5213 in.)

  5. INSPECT 2ND BRAKE CLUTCH DISC 
    1. Check to see if the sliding surface of the disc, plate and flange are worn or burnt.
      Fig 5: Identifying 2nd Brake Clutch Disc
      GTY157841Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      If necessary, replace them.

      NOTE:
      • If the lining of the disc is peeling off or discolored, or if even a part of the printed number is defaced, replace all the discs.
      • Before assembling new discs, soak them in ATF for at least 15 minutes.
  6. INSPECT 1ST AND REVERSE BRAKE CLUTCH DISC 
    1. Check to see if the sliding surface of the disc, plate and flange are worn or burnt.
      Fig 6: Identifying 1st And Reverse Brake Clutch Disc
      GTY166410Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      If necessary, replace them.

      NOTE:
      • If the lining of the disc is peeling off or discolored, or if even a part of the groove is defaced, replace all the discs.
      • Before assembling new discs, soak them in ATF for at least 15 minutes.
  7. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY 
    1. Using a vernier caliper, measure the free length of the 1st and reverse brake return spring together with the spring seat.
      Fig 7: Measuring Free Length Of 1St And Reverse Brake Return Spring
      GTY157827Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard free length

      15.51 mm (0.6106 in.)

  8. INSPECT MULTIPLE DISC CLUTCH HUB 
    1. Using a caliper gauge, measure the inside diameter of the forward clutch hub bush.
      Fig 8: Measuring Inside Diameter Of Forward Clutch Hub Bush
      GTY165059Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard inside diameter

      23.025 to 23.045 mm (0.9065 to 0.9073 in.)

      Maximum inside diameter

      23.09 mm (0.9091 in.)

      NOTE:
      • When the diameter is over the maximum, replace the multiple disc clutch hub with a new one.
      • Check the contact surface of the bush in the direct clutch shaft. If any scratch or discolor is identified, replace the direct clutch sub-assembly with a new one.

      If the inside diameter is greater than the maximum, replace the forward clutch hub.

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.