Customize Parameters

HINT: 

The following items can be customized.

1. Customizing with the Techstream
   1. Connect the Techstream to the DLC3.
   2. Turn the engine switch on (IG).
   3. Turn the Techstream on.
   4. Enter the following menus: Customize Setting / Smart Key/Access or Warning.
   5. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Park Wait Time (Waiting time to permit unlocking door after locking)	2.5s	Function that sets the period of time (lock confirmation time) that the door is prevented from being unlocked by operating the front door outside handle assembly after an entry lock operation is performed.	0.5s, 1.5s, 2.5s or 5s	Certification ECU (smart key ECU assembly)
      Ignition Available Area (Area in which entry ignition function is available)	All	Function that sets the area that the electrical key transmitter must be in before the engine switch can be operated.	Front or All	Certification ECU (smart key ECU assembly)
      Back Door Opening Operation	Long	Function that sets the way the back door opener switch must be pressed in order to open the back door.	Long, Twice or OFF	Certification ECU (smart key ECU assembly)
      Key Low Battery Warning (Warning when transmitter battery becomes weak)	ON	Enables or disables the sounding of the buzzer when the transmitter battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more.	ON or OFF	Certification ECU (smart key ECU assembly)
      Touch activation Over Threshold	Active	The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed.	Active or Not Active	Certification ECU (smart key ECU assembly)
      Door Unlock Mode2	All	Function that chooses the doors to be operated by entry unlock operation	All or Driver	Certification ECU (smart key ECU assembly)

2. Entry cancel function

   HINT: 

   While the smart key system (for Entry Function) is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter against the engine switch.

   1. The following functions are disabled when the smart key system (for Entry Function) is canceled.
      1. Entry unlock/lock functions
      2. Entry ignition function
      3. Key lock-in prevention function
      4. Entry warning functions
   2. When canceling the system through manual operation:
      1. Make sure the following conditions are met:
         • The engine switch is off.
         • The driver side door is closed.
         • The driver side door is unlocked.
      2. Press the unlock switch of the electrical key transmitter.
      3. Open the driver side door within 5 seconds of completing the step above (driver side door: closed at beginning of step → opened).
      4. With the driver side door open, press the unlock switch of the electrical key transmitter 2 times within 5 seconds of completing the step above.
         NOTE:

         If the driver side door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

      5. Close and open the driver side door twice within 30 seconds of completing the above step (driver side door: open at beginning of step → closed → opened → closed → opened).
      6. With the driver side door open, press the unlock switch of the electrical key transmitter 2 times within 30 seconds of completing the step above.
         NOTE:

         If the driver side door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

      7. Close and open the driver side door within 30 seconds of completing the step above (driver side door: open at beginning of step → closed → opened).
      8. Close the driver side door within 5 seconds of completing the above step.
   3. Perform the following procedure to restore the smart key system (for Entry Function) to the active state from the canceled state.
      1. Perform the procedures to cancel the smart key system (for Entry Function) again.

         HINT: 

         The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.