2012 Scion tC Automatic TransFACTORY OEM SERVICE PROCEDURE

Automatic Transaxle Assembly: Removal: Removal

NOTE:

If automatic transaxle parts are replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary. Refer to PRECAUTION .

  1. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT 
    1. Remove the flywheel housing under cover.
      Fig 1: Flywheel Housing Under Cover
      GTY311720Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using SST, hold the crankshaft pulley.
      Fig 2: Holding Crankshaft Using SST
      GTY313971Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • SST: 09213-54015 
      • SST: 09330-00021 
      • SST: 91551-80650 
    3. Remove the 6 drive plate and torque converter setting bolts.
      Fig 3: Torque Converter Setting Bolt
      GTY311725Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE 

    Refer to REMOVAL

  3. SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY 
    1. Support the automatic transmission with a transmission jack so that it is stable.
  4. REMOVE STARTER ASSEMBLY  . Refer to REMOVAL - Step 8
  5. REMOVE TRANSMISSION WIRE 
    Fig 4: Transmission Wire
    GTY311141Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Detach the clamp and disconnect the transmission wire.
    2. Remove the bolt and transmission wire.
  6. DISCONNECT ENGINE WIRE 
    1. Detach the clamp and disconnect the engine wire.
      Fig 5: Park/Neutral Position Switch Connector
      GTY311139Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the park/neutral position switch connector.
    3. Detach the clamp and disconnect the engine wire.
      Fig 6: Engine Wire & Clamp
      GTY311734Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the bolt and disconnect the engine wire.
    5. Detach the 2 clamps and disconnect the engine wire.
      Fig 7: TCM Connector
      GTY314021Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Detach the claw, turn the lock lever and disconnect the connector from the TCM.
      TEXT IN ILLUSTRATION

      *1 Lock Lever
  7. REMOVE WIRE HARNESS CLAMP BRACKET 
    1. Remove the 2 bolts and 2 clamp brackets from the automatic transaxle assembly.
      Fig 8: Automatic Transaxle Clamp Brackets
      GTY311732Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE OIL COOLER TUBE SUB-ASSEMBLY 
    Fig 9: No. 1 Oil Cooler Inlet Hose And No. 1 Oil Cooler Outlet Hose
    GTY311696Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose from the automatic transaxle assembly.
    2. Remove the bolt and No. 1 oil cooler tube.
  9. REMOVE FLEXIBLE HOSE BRACKET SUB-ASSEMBLY 
    1. Detach the clamp and disconnect the breather plug hose from the flexible hose bracket.
      Fig 10: Breather Plug Hose
      GTY311728Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt and flexible hose bracket from the automatic transaxle assembly.
      Fig 11: Flexible Hose Bracket
      GTY311729Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE FRONT ENGINE MOUNTING BRACKET 
    1. Remove the 3 bolts and front engine mounting bracket from the automatic transaxle assembly.
      Fig 12: Front Engine Mounting Bracket
      GTY311731Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE REAR ENGINE MOUNTING BRACKET 
    1. Remove the 3 bolts and rear engine mounting bracket from the automatic transaxle assembly.
      Fig 13: Rear Engine Mounting Bracket
      GTY310300Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE ENGINE MOUNTING BRACKET LH 
    1. Remove the 4 bolts and engine mounting bracket LH from the automatic transaxle assembly.
      Fig 14: Engine Mounting Bracket (LH)
      GTY310299Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE TCM 
    1. Remove the 2 bolts and TCM from the automatic transaxle assembly.
      Fig 15: TCM And Bolts Location
      GTY298291Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET 
    1. Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle assembly.
      Fig 16: No. 1 Transmission Control Cable Bracket
      GTY312329Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY  See step  5
  16. REMOVE TRANSMISSION CASE PLUG ASSEMBLY 
    1. Remove the transmission case plug from the automatic transaxle assembly.
      Fig 17: View Of Automatic Transaxle Assembly Case Plug
      GTY294697Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY 
    1. Remove the 9 bolts, and then remove the automatic transaxle assembly from the engine assembly.
      Fig 18: Automatic Transaxle Assembly Bolts
      GTY304944Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.