Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Driver Side Power Window Does Not Operate With Power Window Master Switch: Procedure
- CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
- Disconnect the E1 power window regulator master switch assembly connector.
- Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection Switch Condition Specified Condition E1-15 (B) - Body ground Ignition switch ON 11 to 14 V - Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition E1-7 (E) - Body ground Always Below 1 Ω TEXT IN ILLUSTRATION*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)
NG → REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step
- INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
- Remove the power window regulator master switch assembly. Refer to REMOVAL .
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Switch Condition Specified Condition 10 (U) - 15 (B) UP Below 1 Ω 7 (E) - 12 (D) 12 (D) - 15 (B) DOWN 7 (E) - 10 (U) 12 (D) - 15 (B) AUTO DOWN 7 (E) - 10 (U)
NG → See step 6
OK: Go to next step
- CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
- Disconnect the E1 power window regulator master switch assembly connector.
- Disconnect the E2 power window regulator motor assembly LH connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition E1-12 (D) - E2-1 Always Below 1 Ω E1-10 (U) - E2-2 Always Below 1 Ω E1-12 (D) or E2-1 - Body ground Always 10 kΩ or higher E1-10 (U) or E2-2 - Body ground Always 10 kΩ or higher
NG → REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step
- INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
- Remove the power window regulator motor assembly LH. Refer to REMOVAL .
- Apply battery voltage to connector terminals 1 and 2.
- Check that the window regulator motor moves smoothly as follows.
OK
Measurement Condition Specified Condition Battery positive (+) → 1
Battery negative (-) → 2Motor gear rotates counterclockwise Battery positive (+) → 2
Battery negative (-) → 1Motor gear rotates clockwise TEXT IN ILLUSTRATION*1 Motor Gear Clockwise Counterclockwise
NG → See step 5
OK → See step 7
- REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH. Refer to REMOVAL
- REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY. Refer to REMOVAL
- REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY. Refer to REMOVAL
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
