Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Vehicle Stability Control System: Calibration: Calibration
- DESCRIPTION
- After replacing VSC-related components, clear and read the sensor calibration data.
- Follow the chart to perform calibration.
Part Replaced Necessary Operation Brake actuator assembly (Skid control ECU) - Clearing zero point calibration data
- Yaw rate and acceleration sensor zero point calibration
- Steering angle sensor zero point calibration
Yaw rate and acceleration sensor - Clearing zero point calibration data
- Yaw rate and acceleration sensor zero point calibration
- Steering angle sensor zero point calibration
Steering angle sensor (Spiral with sensor cable sub-assembly) - Clearing zero point calibration data
- Yaw rate and acceleration sensor zero point calibration
- Steering angle sensor zero point calibration
- OBTAIN ZERO POINT OF YAW RATE AND ACCELERATION SENSOR AND STEERING ANGLE SENSOR (When Using the Techstream) NOTE:
- While obtaining the zero points, keep the vehicle stationary and do not vibrate, tilt, move, or shake it (do not start the engine).
- Be sure to perform this procedure on a level surface (with an inclination of less than 1%).
- Clear the zero point calibration data.
- Turn the ignition switch off.
- Check that the steering wheel is centered.
- for Manual Transaxle:
Check that the shift lever is in neutral and apply the parking brake.
for Automatic Transaxle:
Check that the shift lever is in P.
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON.
- Turn the Techstream on.
- Enter the following menus: Chassis / ABS/VSC/TRAC / Reset Memory.
- Check that the slip indicator light comes on.
- Turn the ignition switch off.
- Perform zero point calibration of the yaw rate and acceleration sensor.
- Turn the ignition switch off.
- Check that the steering wheel is centered.
- for Manual Transaxle:
Check that the shift lever is in neutral and apply the parking brake.
for Automatic Transaxle:
Check that the shift lever is in P.
NOTE:DTCs C1210 (Zero Point Calibration of Yaw Rate Sensor Undone) and C1336 (Zero Point Calibration of Acceleration Sensor Undone) are stored if the shift lever is not in P (for Automatic Transaxle) or the parking brake is not applied (for Manual Transaxle).
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON.
- Turn the Techstream on.
- Switch the skid control ECU to test mode using the Techstream.
Enter the following menus: Chassis / ABS/VSC/TRAC / Test Mode.
- Keep the vehicle stationary on a level surface for 5 seconds or more.
- Check that the slip indicator light blinks in the test mode pattern (0.125 seconds on and 0.125 seconds off).
HINT:
- If the slip indicator light does not blink, perform zero point calibration again.
- Zero point calibration is performed only once after the system enters test mode.
- Calibration cannot be performed again until the stored data is cleared.
- Turn the ignition switch off and disconnect the Techstream.
- Drive the vehicle straight ahead at 35 km/h (22 mph) or more for approximately 5 seconds.
- OBTAIN ZERO POINT OF YAW RATE AND ACCELERATION SENSOR AND STEERING ANGLE SENSOR (When Using SST Check Wire) NOTE:
- While obtaining the zero points, keep the vehicle stationary and do not vibrate, tilt, move, or shake it (do not start the engine).
- Be sure to perform this procedure on a level surface (with an inclination of less than 1%).
- Clear the zero point calibration data.
- Turn the ignition switch off.
- Check that the steering wheel is centered.
- for Manual Transaxle:
Check that the shift lever is in neutral and apply the parking brake.
for Automatic Transaxle:
Check that the shift lever is in P.
- Turn the ignition switch to ON.
- The ABS warning light and slip indicator light come on for 3 seconds to indicate that the initial check is completed.
- Using SST, connect and disconnect terminals 12 (TS) and 4 (CG) of the DLC3 4 times or more within 8 seconds.TEXT IN ILLUSTRATION
*a Front view of DLC3 - SST: 09843-18040
- Check that the slip indicator light comes on.
- Perform zero point calibration of the yaw rate and acceleration sensor.
- Turn the ignition switch off.
- Check that the steering wheel is centered.
- for Manual Transaxle:
Check that the shift lever is in neutral and apply the parking brake.
for Automatic Transaxle:
Check that the shift lever is in P.
NOTE:DTCs 36 (Zero Point Calibration of Yaw Rate Sensor Undone) and 39 (Zero Point Calibration of Acceleration Sensor Undone) are stored if the shift lever is not in P (for Automatic Transaxle) or the parking brake is not applied (for Manual Transaxle).
- Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.TEXT IN ILLUSTRATION
*a Front view of DLC3 - SST: 09843-18040
- Turn the ignition switch to ON.
- Keep the vehicle stationary on a level surface for 5 seconds or more.
- Check that the slip indicator light blinks in the test mode pattern (0.125 seconds on and 0.125 seconds off).
HINT:
- If the slip indicator light does not blink, perform zero point calibration again.
- Zero point calibration is performed only once after the system enters test mode.
- Calibration cannot be performed again until the stored data is cleared.
- Turn the ignition switch off and disconnect SST from the DLC3.
- Drive the vehicle straight ahead at 35 km/h (22 mph) or more for approximately 5 seconds.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
