2009 Scion xD AutomaticFACTORY OEM SERVICE PROCEDURE

Power Window Regulator Motor: Installation

  1. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY 
    1. Apply MP grease to the sliding and rotating areas of the regulator motor.
    2. Using "TORX" socket wrench T25, install the front power window regulator motor assembly with the 3 screws.

      Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

      Fig 1: Locating Front Power Window Regulator Motor Assembly Screws
      G05391280Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY  (See REASSEMBLY )
  3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY  (See REASSEMBLY )
  4. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY 
    1. Install the rear door window division bar with the 2 bolts and screw.

      Torque: 6.2 N*m (63 kgf*cm, 54 in.*lbf) 

      Fig 2: Locating Rear Door Window Division Bar With Bolts
      G05403051Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the rear door weatherstrip.
      3. Fig 3: Locating Rear Door Weatherstrip
      G05403050Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. INSTALL REAR DOOR GLASS RUN  (See REASSEMBLY )
  6. INSTALL REAR DOOR SERVICE HOLE COVER  (See REASSEMBLY )
  7. INSTALL REAR DOOR TRIM BRACKET  (See REASSEMBLY )
  8. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY  (See REASSEMBLY )
  9. INSTALL REAR DOOR INSIDE HANDLE BEZEL  (See REASSEMBLY )
  10. INSTALL REAR DOOR ARMREST BASE UPPER PANEL  (See REASSEMBLY )
  11. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY 
    1. Apply MP grease to the sliding and rotating areas of the regulator motor.
    2. Using "TORX" socket wrench T25, install the front power window regulator motor assembly with the 3 screws.

      Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

      Fig 4: Installing Front Power Window Regulator Motor Assembly With Screws
      G05391277Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY  (See REASSEMBLY )
  13. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY  (See REASSEMBLY )
  14. INSTALL FRONT DOOR SERVICE HOLE COVER  (See REASSEMBLY )
  15. INSTALL FRONT DOOR TRIM BRACKET  (See REASSEMBLY )
  16. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY  (See REASSEMBLY )
  17. INSTALL FRONT DOOR INSIDE HANDLE BEZEL  (See REASSEMBLY )
  18. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH  (See REASSEMBLY )
  19. INSTALL FRONT ARMREST BASE UPPER PANEL  (See REASSEMBLY )
  20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 

    Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.