Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
How To Proceed With Troubleshooting
HINT:Â
- Use this procedure to troubleshoot the push button start function.
- Techstream should be used in steps 3, 4 and 6.
- When troubleshooting the push-button function using Techstream with the engine switch off, connect Techstream to the vehicle and repeat turning any of the courtesy light switches on and off until communication between the tester and the vehicle begins (the interval between ON and OFF should be less than 1.5 sec.).
- VEHICLE BROUGHT TO WORKSHOPÂ
NEXT: Go to next stepÂ
- CUSTOMER PROBLEM ANALYSIS CHECK AND SYMPTOM CHECKÂ
HINT:Â
Refer to HOW TO PROCEED WITH TROUBLESHOOTING
NEXT: Go to next stepÂ
- INSPECT COMMUNICATION FUNCTION OF MULTIPLEX COMMUNICATION SYSTEM (BEAN)Â
- Use Techstream to check for normal function of the multiplex communication system.
- (ECU not connected, communication line malfunctioning) Without code outputs, proceed to A.
- (ECU not connected, communication line malfunctioning) With code outputs, proceed to B.
B → Go to  MULTIPLEX COMMUNICATION SYSTEM MULTIPLEX COMMUNICATION SERVICE INFORMATIONÂ
A: Go to next stepÂ
- Use Techstream to check for normal function of the multiplex communication system.
- CHECK DTCÂ
- Check for DTCs and note any codes that are output.
- Delete the DTC.
HINT:Â
After DTCs are all cleared, check if the trouble occurs again 6 seconds after the engine switch is turned on (IG).
- Recheck for DTCs. Try to prompt the DTC by simulating the original activity that the DTC suggests.
- If the DTC does not reoccur, proceed to A.
- If the DTC reoccurs, proceed to B.
B → DTC CHARTÂ
A: Go to next stepÂ
- INSPECT BASIC OPERATIONÂ
- Turn the engine switch on (START) and check that the engine starts normally. Make sure the brake pedal is depressed and the shift position is in P at this time.
- Check that the engine switch mode can be changed by pushing the engine switch.
HINT:Â
Without depressing the brake pedal, push the engine switch repeatedly. Engine switch mode should turn from OFF to ON (ACC) to ON (IG) and back to OFF.
With the brake pedal depressed, push the engine switch repeatedly. Engine switch mode should turn to ENGINE START from any status.
OK
Engine can start normally
NEXT: Go to next stepÂ
- PROBLEM SYMPTOMS TABLEÂ
- If the fault is not listed in the problem symptoms table, proceed to A.
- If the fault is listed in the problem symptoms table, proceed to B.
B → Go to   8 step 8Â
A: Go to next stepÂ
- OVERALL ANALYSIS AND TROUBLE SHOOTINGÂ
- Data List / Active Test. Refer to DATA LIST / ACTIVE TESTÂ
- Inspection with Techstream (Data List)
- Inspection with Techstream (Active Test)
- Terminal of ECU. Refer to TERMINALS OF ECUÂ
NEXT: Go to next stepÂ
- Data List / Active Test. Refer to DATA LIST / ACTIVE TESTÂ
- ADJUST, REPAIR OR REPLACEÂ
NEXT: Go to next stepÂ
- CONFIRMATION TESTÂ
NEXT → ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
