Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Scion xA AutomaticFACTORY OEM SERVICE PROCEDURE
Service Data
SERVICE DATA
| U340E | ||
| Line pressure (wheel locked) at stall (Throttle valve fully opened) | D position R position |
1, 107 to 1, 225 kPa (11.3 to 12.5 kgf/cm2
, 161 to 178 psi) 1, 695 to 1, 813 kPa (17.3 to 18.5 kgf/cm2 , 246 to 263 psi) |
| Engine stall revolution | - | 2, 050 to 2, 550 rpm |
| Time lag | N --> D position N --> R position |
Less than 1.2 seconds Less than 1.5 seconds |
| Engine idle speed (A/C OFF) | N position | 650 to 750 rpm |
| Drive plate runout | Maximum | 0.20 mm (0.0079 in.) |
| Differential oil seal drive in depth | LH side RH side |
5.4 to 6.4 mm (0.213 to 0.252 in.) 1.5 to 2.5 mm (0.059 to 0.098 in.) |
| Shift schedule D position (Throttle valve fully opened) |
1 --> 2 2 --> 3 3 --> 4 4 --> 3 3 --> 2 2 --> 1 |
50 to 55 km/h (31 to 34 mph) 94 to 102 km/h (58 to 63 mph) 147 to 156 km/h (91 to 97 mph) 142 to 151 km/h (88 to 94 mph) 89 to 96 km/h (55 to 60 mph) 41 to 46 km/h (25 to 29 mph) |
| Throttle valve fully closed) | 3 --> 4 4 --> 3 |
40 to 44 km/h (25 to 27 mph) 30 to 34 km/h (19 to 21 mph) |
| 2 position Throttle valve fully opened) |
1 --> 2 3 --> 2 2 --> 1 |
50 to 55 km/h (31 to 34 mph) 89 to 96 km/h (55 to 60 mph) 41 to 46 km/h (25 to 29 mph) |
| L position Throttle valve fully opened) |
3 --> 2 2 --> 1 |
89 to 96 km/h (55 to 60 mph) 44 to 48 km/h (27 to 30 mph) |
| Lock-up point D range |
(Throttle valve opening 5%) Lock-up ON 3 --> 3L 4 --> 4L Lock-up OFF 4L --> 4 3L -->3 |
94 to 102 km/h (58 to 63 mph) 54 to 59 km/h (34 to 37 mph) 52 to 56 km/h (32 to 35 mph) 89 to 96 km/h (55 to 60 mph) |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.