Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
M/T Models
- CHECK OVERALL FUNCTION-IÂ
With CONSULT-IIÂ
- Turn ignition switch ON.
- Select "BRAKE SW1" in "DATA MONITOR" mode with CONSULT-II.
- Check "BRAKE SW1" indication under the following conditions.
INDICATION CONDITIONCONDITION INDICATION Clutch pedal and/or brake pedal: Slightly depressed OFF Clutch pedal and brake pedal: Fully released ON Without CONSULT-IIÂ
- Turn ignition switch ON.
- Check voltage between ECM terminal 108 and ground under the following conditions.
VOLTAGE REFERENCECONDITION VOLTAGE Clutch pedal and/or brake pedal: Slightly depressed Approximately 0V Clutch pedal and brake pedal: Fully released Battery voltage OK or NGÂ
OK : GO TO Â 2.
NG : GO TO Â 3.
- CHECK OVERALL FUNCTION-IIÂ
With CONSULT-IIÂ
Check "BRAKE SW2" indication in "DATA MONITOR" mode.
INDICATION CONDITIONCONDITION INDICATION Brake pedal: Fully released OFF Brake pedal: Slightly depressed ON Without CONSULT-IIÂ
Check voltage between ECM terminal 101 and ground under the following conditions.
VOLTAGE REFERENCECONDITION VOLTAGE Brake pedal: Fully released Approximately 0V Brake pedal: Slightly depressed Battery voltage OK or NGÂ
OK : INSPECTION ENDÂ
NG : GO TO Â 10.
- CHECK ASCD CLUTCH SWITCH POWER SUPPLY CIRCUITÂ
- Turn ignition switch OFF.
- Disconnect ASCD clutch switch harness connector.
- Turn ignition switch ON.
- Check voltage between ASCD clutch switch terminal 1 and ground with CONSULT-II or tester.
Voltage: Battery voltageÂ
OK or NGÂ
OK : GO TO Â 8.
NG : GO TO Â 4.
- CHECK ASCD BRAKE SWITCH POWER SUPPLY CIRCUITÂ
- Turn ignition switch OFF.
- Disconnect ASCD brake switch harness connector.
- Turn ignition switch ON.
- Check voltage between ASCD brake switch terminal 1 and ground with CONSULT-II or tester.
Voltage: Battery voltageÂ
OK or NGÂ
OK : GO TO Â 6.
NG : GO TO Â 5.
- 5.DETECT MALFUNCTIONING PARTÂ
Check the following.
- Fuse block (J/B) connector E160
- 10A fuse
- Harness for open or short between ASCD brake switch and fuse
: Repair open circuit or short to ground in harness or connectors.
- CHECK ASCD BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Turn ignition switch OFF.
- Check harness continuity between ASCD brake switch terminal 2 and ASCD clutch switch terminal 1.
Refer to WIRING DIAGRAMÂ .
Continuity should exist .
- Also check harness for short to ground and short to power.
OK or NGÂ
OK : GO TO Â 7.
NG : Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK ASCD BRAKE SWITCHÂ
Refer to "COMPONENT INSPECTIONÂ ".
OK or NGÂ
OK : GO TO Â 14.
NG : Replace ASCD brake switch.
- CHECK ASCD BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Turn ignition switch OFF.
- Disconnect ECM harness connector.
- Check harness continuity between ECM terminal 108 and ASCD clutch switch terminal 2.
Refer to WIRING DIAGRAMÂ .
Continuity should exist .
- Also check harness for short to ground and short to power.
OK or NGÂ
OK : GO TO Â 9.
NG : Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK ASCD CLUTCH SWITCHÂ
Refer to "COMPONENT INSPECTIONÂ ".
OK or NGÂ
OK : GO TO Â 14.
NG : Replace ASCD clutch switch.
- CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUITÂ
- Turn ignition switch OFF.
- Disconnect stop lamp switch harness connector.
- Check voltage between stop lamp switch terminal 1 and ground with CONSULT -II or tester.
Voltage: Battery voltageÂ
OK or NGÂ
OK : GO TO Â 12.
NG : GO TO Â 11.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Fuse block (J/B) connector E160
- 10A fuse
- Harness for open or short between stop lamp switch and battery
: Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK STOP LAMP SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Disconnect ECM harness connector.
- Check harness continuity between ECM terminal 101 and stop lamp switch terminal 2.
Refer to WIRING DIAGRAMÂ .
Continuity should exist .
- Also check harness for short to ground and short to power.
OK or NGÂ
OK : GO TO Â 13.
NG : Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK STOP LAMP SWITCHÂ
Refer to "COMPONENT INSPECTIONÂ ".
OK or NGÂ
OK : GO TO Â 14.
NG : Replace stop lamp switch.
- CHECK INTERMITTENT INCIDENTÂ
Refer to "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ".
: INSPECTION ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
