Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2006 Saturn Ion Red LineFACTORY OEM SERVICE PROCEDURE
Body Control Module (BCM) C2
Body Control Module (BCM) C2
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | - | - | Not Used |
| 2 | OG | 40 | Battery Positive Voltage |
| 3 | OG | 240 | Battery Positive Voltage |
| 4 | - | - | Not Used |
| 5 | BN | 9 | Park Lamp Supply Voltage (T82) |
| 6 | OG | 840 | Battery Positive Voltage |
| 7 | PK | 1200 | Headlamp High Beam Signal |
| 8 | L-BU | 20 | Stop Lamp Switch Signal |
| 9 | PK | 339 | Ignition 1 Voltage (w/o Redline) |
| 10 | PK | 339 | Ignition 1 Voltage (M/T) |
| 11 | PK | 339 | Ignition 1 Voltage |
| 12 | - | - | Not Used |
| 13 | OG | 52 | Blower Motor Supply Voltage |
| 14 | BN | 41 | Ignition 3 Voltage |
| 15 | BN | 141 | Ignition 3 Voltage |
| 16 | - | - | Not Used |
| 17 | OG | 1040 | Battery Positive Voltage |
| 18 | OG | 1440 | Battery Positive Voltage |
| 19 | OG | 1440 | Battery Positive Voltage |
| 20 | - | - | Not Used |
| 21 | OG | 40 | Battery Positive Voltage |
| 22 | YE | 143 | Accessory Voltage |
| 23 | YE | 143 | Accessory Voltage (A/T) |
| 24-27 | - | - | Not Used |
| 28 | PK | 339 | Ignition 1 Voltage (2.2L, 2.4L w/M/T) |
| 29 | YE | 343 | Accessory Voltage |
| 30 | PK | 343 | Accessory Voltage (UXE) |
| 31 | OG | 52 | Blower Motor Supply Voltage |
| 32 | OG | 52 | Blower Motor Supply Voltage |
| 33 | YE | 1139 | Ignition 1 Voltage |
| 34 | YE | 1139 | Ignition 1 Voltage (w/o Redline) |
| 35 | PK | 1539 | Ignition 1 Voltage |
| 36 | - | - | Not Used |
| 37 | OG | 1140 | Battery Positive Voltage |
| 38 | OG | 140 | Battery Positive Voltage |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
