Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Scan Tool Data Definitions
- ABS Active
-
The scan tool displays the active status of the ABS.
- Brake Fluid Level Switch
-
The scan tool displays the status of the brake fluid level.
- Brake Pressure Sensor
-
The scan tool displays the master cylinder hydraulic pressure applied to the system.
- Brake Pressure Sensor Input
-
The scan tool displays the pressure sensor signal voltage.
- Brake Temp Status
-
The electronic brake control module (EBCM) calculates the brake rotor temperature. If the EBCM determines that the rotor temperature is to high, brake intervention traction control is temporarily inhibited.
- DRP Active
-
The scan tool displays the active status of the dynamic rear proportioning (DRP)
- DRP Disabled
-
The scan tool displays the functional status of the DRP.
- Ignition Voltage Signal
-
The scan tool displays ignition voltage from 0 to 17 volts.
- Initial Brake Apply Signal
-
The scan tool displays the applied state of the brake pedal.
- Lateral Accelerometer Signal
-
The scan tool displays the sensor voltage output and lateral g force.
- Left TCS Isolation Solenoid Command
-
The scan tool displays the status of the left traction control system (TCS) isolation solenoid.
- Left TCS Prime Solenoid Command
-
The scan tool displays the status of the left traction TCS primary solenoid.
- LF Wheel Speed
-
The scan tool displays the actual speed of the left front wheel.
- LR Wheel Speed
-
The scan tool displays the actual speed of the left rear wheel.
- Moderate Brake Apply Signal
-
The scan tool displays applied when the brake pedal is depressed firmly.
- Pump Motor Relay Command
-
The scan tool displays the commanded state of the pump motor relay.
- Pump Motor Relay Feedback Voltage
-
The scan tool displays the actual on/off state of the pump motor relay.
- Right TCS Isolation Solenoid Command
-
The scan tool displays the status of the right TCS isolation solenoid.
- Left TCS Prime Solenoid Command
-
The scan tool displays the status of the left traction TCS primary solenoid.
- RF Wheel Speed
-
The scan tool displays the actual speed of the right front wheel.
- Rough Road Detected
-
The EBCM calculates the condition of the road surface, this information is sent to the PCM via serial data messages. The PCM uses this information for misfire detection.
- RR Wheel Speed
-
The scan tool displays the actual speed of the right rear wheel.
- Solenoid Relay Command
-
The scan tool displays the commanded state of the solenoid relay.
- Steering Position Sensor
-
The scan tool displays the steering wheel position in degrees.
- Stoplamp Pedal Switch
-
The scan tool displays the applied state of the brake pedal.
- Stoplamp Pedal Switch Signal
-
The scan tool displays the brake pedal position (BPP) sensor voltage.
- Switched Battery Voltage
-
The scan tool displays 0 to 17 volts. The level of the internal EBCM switched battery voltage available to the solenoid valves and pump motor.
- SWPS Signal 1
-
The scan tool displays the voltage output of signal 1 of the steering wheel position sensor (SWPS).
- SWPS Signal 2
-
The scan tool displays the voltage output of signal 2 of the SWPS.
- TCS Active
-
The scan tool displays Yes or No. The active status of the TCS. Indicates if TCS is currently active.
- TCS Active Indicator/Message
-
The scan tool displays Off or On. Indicates if the EBCM is commanding the Traction Engaged message to be displayed by the DIC.
- TCS Active
-
The scan tool displays the active status of the TCS.
- TCS Enabled
-
The scan tool displays the operating status of the TCS.
- Traction Control Status
-
The scan tool displays the active status of the TCS.
- Torque Request Signal
-
The scan tool displays the requested engine torque to perform traction control sent by the EBCM.
- Vehicle Speed
-
The scan tool displays the vehicle speed.
- VSES Active
-
The scan tool displays the active status of the vehicle stability enhancement system (VSES).
- VSES Enabled
-
The scan tool displays the operating status of the VSES.
- Yaw Rate Sensor
-
The scan tool displays vehicle yaw rate in degrees of vehicle rotation per second (Β°/sec).
- Yaw Rate Signal
-
The scan tool displays the sensor signal voltage.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
