Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSATURN2000LS1 L4-2.2L VIN FREPAIR AND DIAGNOSISWINDOWS AND GLASSWINDOWSWINDOW GLASSSERVICE PRECAUTIONS
2000 Saturn LS1 L4-2.2L VIN F
Window Glass: Service Precautions
2000 Saturn LS1 L4-2.2L VIN FSECTION Service Precautions
STATIONARY GLASS
CAUTION:
- WHEN USING POWER TOOLS THAT MAY CREATE SMOKE WHEN CUTTING URETHANE SEALANT, WORK SHOULD BE DONE IN A WELL VENTILATED AREA AND/OR WITH A NIOSH/MSHA APPROVED AIR SUPPLIED RESPIRATOR TO PREVENT POSSIBLE HARMFUL EXPOSURE.
WHEN THE URETHANE ADHESIVE IS HEATED ENOUGH TO GIVE OFF SMOKE, HIGH LEVELS OF METHYLENE DIISOCYANATE (MDI) MAY BE PRESENT.
UNPROTECTED EXPOSURE TO METHYLENE DIISOCYANATE (MDI) MAY RESULT IN SEVERE, CHRONIC, DEBILITATING RESPIRATORY PROBLEMS.
- WHEN REPLACING A WINDSHIELD, BACKGLASS, OR QUARTER GLASS (COUPE) URETHANE ADHESIVE (PART NO.12345633) OR EQUIVALENT MUST BE USED TO MAINTAIN ORIGINAL INSTALLATION INTEGRITY. FAILURE TQ USE URETHANE ADHESIVE WILL RESULT IN POOR RETENTION OF THE WINDSHIELD WHICH MAY ALLOW UNRESTRAINED OCCUPANT TO BE EJECTED FROM THE VEHICLE WITH RESULTING PERSONAL INJURY
ADHESIVE SERVICE KIT
Adhesive Kit No. 12345633 (urethane adhesive) or equivalent contains some of the items needed to replace a urethane adhesive installed glass.
Additional items required:
- Isopropyl alcohol for cleaning edge of glass and bonding surfaces.
- Household cartridge type caulking gun.
- Commercial type razor knife (for cutting and trimming urethane).
- Power glass removal tool.
- Glass sealant remover (cold knife). Piano wire and handles.
CAUTION:
- WHEN USING POWER TOOLS THAT MAY CREATE SMOKE WHEN CUTTING URETHANE SEALANT, WORK SHOULD BE DONE IN A WELL VENTILATED AREA AND/OR WITH A NIOSH/MSHA APPROVED AIR SUPPLIED RESPIRATOR TO PREVENT POSSIBLE HARMFUL EXPOSURE.
WHEN THE URETHANE ADHESIVE IS HEATED ENOUGH TO GIVE OFF SMOKE, HIGH LEVELS OF METHYLENE DIISOCYANATE (MDI) MAY BE PRESENT.
UNPROTECTED EXPOSURE TO METHYLENE DIISOCYANATE (MDI) MAY RESULT IN SEVERE, CHRONIC, DEBILITATING RESPIRATORY PROBLEMS.
- WHEN REPLACING A WINDSHIELD, BACKGLASS, OR QUARTER GLASS (COUPE) URETHANE ADHESIVE (PART NO.12345633) OR EQUIVALENT MUST BE USED TO MAINTAIN ORIGINAL INSTALLATION INTEGRITY. FAILURE TQ USE URETHANE ADHESIVE WILL RESULT IN POOR RETENTION OF THE WINDSHIELD WHICH MAY ALLOW UNRESTRAINED OCCUPANT TO BE EJECTED FROM THE VEHICLE WITH RESULTING PERSONAL INJURY
ADHESIVE SERVICE KIT
Adhesive Kit No. 12345633 (urethane adhesive) or equivalent contains some of the items needed to replace a urethane adhesive installed glass.
Additional items required:
- Isopropyl alcohol for cleaning edge of glass and bonding surfaces.
- Household cartridge type caulking gun.
- Commercial type razor knife (for cutting and trimming urethane).
- Power glass removal tool.
- Glass sealant remover (cold knife). Piano wire and handles.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.