Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSATURN1997SC1 AUTOMATICREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSCOMMON SPECS & PROCEDURESSPECIFICATIONS INDEX
1997 Saturn SC1 Automatic
Specifications Index
1997 Saturn SC1 AutomaticSECTION Specifications Index
S SERIES SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | A/C SYSTEM SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | 148 Ft. lbs. (210 N.m) | ||
| Battery | CAPACITIES | ||
| Brakes | |||
| Bleeding Sequence | RR, LF, LR, RF | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | DRUM BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | BELT ADJUSTMENT | ||
| Drive Belt Routing | See appropriate figure under SERPENTINE BELT ROUTING | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | 18 psi | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | 13 psi (.91 kg/cm2 ) at curb idle and 36 psi (2.5 kg/cm2 ) at 2000 RPM | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| Flexplate to Crankshaft | 44 Ft. lbs. (60 N.m) | ||
| Flywheel to Crankshaft | 59 Ft. lbs. (80 N.m) | ||
| Fuel System | |||
| Pressure Specification | 46-94 psi (317-648 kPa) | ||
| Fuel Pressure Test Procedure | FUEL SYSTEM PRESSURE TEST | ||
| Fuel Filter Location | In fuel feed line under vehicle mounted on driver's side of engine compartment frame rail. | ||
| Fuel Filter R & I | FUEL FILTER | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER | ||
| Ignition Wires (Resistance) | 12,000 Ohms Maximum | ||
| Ignition Wires (Routing) | FIRING ORDER | ||
| Spark Plug | |||
| VIN 7 | |||
| Type | AC 41-627 | ||
| Gap | .040 In. (1.02 mm) | ||
| Torque | 20 Ft. lbs. (27 N.m) | ||
| VIN 8 | |||
| Type | AC 41-628 | ||
| Gap | .040 In. (1.02 mm) | ||
| Torque | 20 Ft. lbs. (27 N.m) | ||
| Starting | |||
| Starter | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 103 Ft. lbs. (140 N.m) | ||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.