Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2010 Saab 9-5FACTORY OEM SERVICE PROCEDURE
Traction Control: TCS/Esp
- Technical data
- Technical description
- Fault diagnosis, fault codes
- TCS/ESP DTC Index
- DTC B0000: Vehicle Speed Information Circuit Invalid Data; DTC C0055: Invalid Data Received From Electronic Brake Control Module Malfunction; DTC C0246: Invalid Data Received From Electronic Brake Control Module Malfunction; DTC C1207: Left Front Wheel Speed Sensor Circuit High Input Malfunction; DTC C1208: Right Front Wheel Speed Sensor Circuit High Input Malfunction; DTC C1209: Left Rear Wheel Speed Sensor Circuit High Input Malfunction; DTC C1210: Right Rear Wheel Speed Sensor Circuit High Input Malfunction; DTC C1221: Left Front Wheel Speed Sensor Circuit Malfunction; DTC C1222: Right Front Wheel Speed Sensor Circuit Malfunction; DTC C1223: Left Rear Wheel Speed Sensor Circuit Malfunction; DTC C1224: Right Rear Wheel Speed Sensor Circuit Malfunction; DTC C1225: Left Front Wheel Speed Sensor Circuit Performance Malfunction; DTC C1226: Right Front Wheel Speed Sensor Circuit Malfunction; DTC C1227: Left Rear Wheel Speed Sensor Circuit Malfunction; DTC C1228: Right Rear Wheel Speed Sensor Circuit Malfunction; DTC C1232: Left Front Wheel Speed Sensor Circuit Low Input Malfunction; DTC C1233: Right Front Wheel Speed Sensor Circuit Low Input Malfunction; DTC C1234: Left Rear Wheel Speed Sensor Circuit Low Input Malfunction; DTC C1235: Right Rear Wheel Speed Sensor Circuit Low Input Malfunction
- DTC B2745: Traction Control Switch Circuit Short to Ground
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Component Testing
- Repair Instructions
- DTC C0035: Left Front Wheel Speed Sensor Circuit; DTC C0040: Right Front Wheel Speed Sensor Circuit; DTC C0045: Left Rear Wheel Speed Sensor Circuit; DTC C0050: Right Rear Wheel Speed Sensor Circuit
- Diagnostic Instructions
- DTC Descriptors
- Diagnostic Fault Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Component Testing
- Repair Instructions
- DTC C0110: Pump Motor Circuit
- DTC C0131: Traction Control System Pressure Circuit
- Diagnostic Instructions
- DTC Descriptors
- Diagnostic Fault Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Repair Instructions
- DTC C0161: Antilock Braking System Brake Switch Circuit
- DTC C0187: Lateral Acceleration Sensor Circuit Not Plausible; DTC C0196: Yaw Rate Circuit Not Plausible; DTC C019B: Yaw Rate Signal Not Plausible; DTC C0287: Longitudinal Acceleration Sensor Circuit Not Plausible; DTC C0297: Lost Communication with Yaw Rate Sensor Checksum Error
- DTC C0242: Powertrain Control Module Indicated Traction Control Malfunction; DTC P0856: Traction Control Torque Request Circuit Malfunction
- DTC C0245: Wheel Speed Sensor Frequency Malfunction
- DTC C0252: Vehicle Stability Control Module Sensors Correlation Malfunction
- DTC C0267: Low Brake Fluid Level Is Indicated
- DTC C0274: Isolation Valve High Temperature; DTC C0275: Dump Valve High Temperature; DTC C0280: Stability System Active Too Long High Temperature
- DTC C0299: Brake Servo Large Vacuum Leakage Registered, Too Many Transitions
- Diagnostic Instructions
- DTC Descriptors
- Diagnostic Fault Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Repair Instructions
- DTC C0460: Steering Wheel Angle Sensor Invalid Data; DTC C0710: Steering Position Signal
- Diagnostic Instructions
- DTC Descriptors
- Diagnostic Fault Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Repair Instructions
- DTC C0558: Calibration Data Calibration Not Learned
- DTC C0569: System Configuration Malfunction
- DTC C1100: Brake pressure sensor 2
- DTC C122E: Tire Size Mismatch Malfunction
- DTC C123C: Electronic Brake Control Module RAM Malfunction; DTC C1255: Electronic Control Unit Performance Malfunction; DTC C1256: Control Module Programming Checksum Error Malfunction
- Traction Control/Stability Control Indicator Malfunction
- Fault diagnosis, symptoms
- Adjustment Replacement
- Time studies - ABS/TCS
- Steering Angle Sensor Centering
- Electronic Brake Control Module Replacement
- Electronic Brake and Traction Control Module with Brake Pressure Modulator Valve Replacement
- Steering Wheel Position Sensor Replacement
- Brake Pressure Modulator Valve Pressure Sensor Calibration
- Front Wheel Speed Sensor Replacement (GNA)
- Front Wheel Speed Sensor Replacement (GNB)
- Rear Wheel Speed Sensor Replacement
- Vehicle Yaw Sensor Learn
- Vehicle Yaw Sensor with Vehicle Lateral and Longitudinal Accelerometer Replacement
- Component location
- Wiring diagram
- Bulletins
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.