2003 Saab 9-3 Arc, AutomaticFACTORY OEM SERVICE PROCEDURE

Connector K

COMPONENT FUNCTION

Pin ( refers to the control module) Color Component / Function In / Out Measurement requirement. Measurement value Measure between
4 VT/WH Control module, glow plug Out Glow plug not activated 10.3 V 5-50
5   Radiator fan circuit 3 Out Radiator fan circuit 3 activated
Radiator fan circuit 3 not activated
< 0.1 V
B+
5-50
5-50
7 YE/BU Power supply measurement Group 3 Out   5 V 7-50
8 BK Sensor ground In   < 0.1 V 8-50
9 YE Reference ground, pedal position sensor 1 In   < 0.1 V 9-50
10 YE/BU Relay, +50 In Rotation of the starter motor B+
< 0.1 V
10-28
14 VT/WH Check Engine warning light Out   B+ 14-50
16 RD/GN Power supply, +15 Out   < 0.1 V 16-B+
17   P bus- (1)     2-3V 17-50
19 YE/GN Clutch switch, cruise control In Unaffected
Depressed
B+
< 0.1 V
19-50
21 VT/WH Reference ground, pedal position sensor 2 In   < 0.1 V 21-50
23 GN/GY Relay, +50 Out Rotation of the starter motor B+
< 0.1 V
10-28
28 YE/BU Main relay Out   < 1 V 28-50
29   P bus+ (1)     2-3V 29-50
30 GN/GY A/C compressor Out Idling, A/C on B+
< 0.5 V
30-50
31 GN/BU Power supply measurement, Group 2 Out   5 V 31-50
32 GY Pressure sensor, A/C In   1-1.5 V 32-50
33 BU/WH Pedal position sensor 1 In Unaffected
Depressed
< 1 V
3.7-3.8 V
33-9
35 GY Glow plug control module, signal In   < 0.5 V 35-50
36 BK/YE Brake switch, cruise control In Unaffected
Depressed
B+
< 0.1 V
36-50
40 BU/WH Brake lights In Unaffected
Depressed
< 1.5 V
B+
40-50
44 OG/WH Atmospheric pressure sensor In   4.2 V 44-50
45 BU/WH Pedal position sensor 2 In Unaffected
Depressed
0.5 V
1.8 V
45-21
49 YE/GY Main relay In   B+ 49-50
50 BK Power ground Out   B+ 50-49
51 YE/GY Main relay     B+ 51-50
52 BK Power ground     B+ 52-49
53 YE/GY Main relay     B+ 53-50
54 BK Power ground     B+ 54-49
55 YE/GY Main relay     B+ 55-49
56 BK Power ground     B+ 56-49
(1) All units connected to the I and P busses transmit signals.
Fig 1: Identifying Connector 595K
G03617251Courtesy of SAAB-SCANIA OF AMERICA, INC.
Chapter Navigation
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.