Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Reading And Writing Values For AWS Control Unit
InformationÂ
The PIWIS Tester II 9818Â instructions take precedence since the description may be different with later Tester releases.
The procedure described here has been structured in general terms; different text or additions may appear in PIWIS Tester II 9818Â .
- Replace control unit. → 696819 REMOVE AND INSTALL AWS CONTROL UNIT NOTE: Voltage drop
- Risk of irreparable damage to control unit
- Risk of damage to control unit
- Fault entries in the control unit
- Coding in the control unit is aborted
- Malfunctions in control unit, even during programming
→ Prior to disconnecting the control unit, switch off ignition and remove ignition key.
→ Ensure that the power supply is not interrupted during programming.
→ Connect a battery charger with a current rating of at least → Nominal value: 40 A to the vehicle battery.
- Connect battery charger to the vehicle.
- Seat calibration position Move passenger's seat longitudinally until flush with the seat rails and to its lowest position.
- Connect the Porsche System Tester PIWIS Tester 9718Â to the vehicle and start the System Tester. Switch on ignition. Press [>>] to continue.
- Select vehicle type.
- Switch from the vehicle type to the list of control units [>>].
- Select AWSÂ with the cursor keys and press the [>>] key.
- Select Control unit replacement with the cursor keys and press the [>>] key.
- The Tester displays several messages and instructions relating to the individual work steps until the message Control unit replacement was completed successfully appears. Press [>>].
- To check the system, select the Actual valuesÂ
menu under the AWSÂ
control unit. Then press [>>].
- 10.1. Select the Weight group (0-4)Â
and Gross weight calibratedÂ
options.
- 10.1.1. If there is no weight on the passenger's seat, compare values (see table below) using the PIWIS Tester. The Passenger Airbag Off indicator light in the center console must not come on.
- 10.1.2. Place the special tool test weight 9742Â on the passenger's seat. The Passenger Airbag Off indicator light in the center console must come on. Compare values (see table below) using the PIWIS Tester.
- 10.1.3. Get an assistant with a body weight of more than 55 kg, for example, to sit on the passenger's seat. The Passenger Airbag Off indicator light in the center console must notÂ
come on. Compare values (see table below) using the PIWIS Tester.
Test state Weight class (0-4) Total weight calibrated (seat in calibration position) No weight on the passenger's seat. 0 → Control value: 0 kg+/-1 kg Special tool test weight 9742 on passenger's seat 1 → Control value: 6.7 kg+/-1 kg Get a person weighing > 55 kg at least to sit on the passenger's seat. 2, 3 or 4 → Control value for person's weight: > 55 kg; person's weight +/- 25 %Â
- 10.1. Select the Weight group (0-4)Â
and Gross weight calibratedÂ
options.
- Read out and erase the fault memories in the Airbag and AWS control unit, perform a test drive and then read out the fault memories again. If faults are found, determine the cause using the PIWIS Tester and correct the faults.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
