2003 Porsche Cayenne TurboFACTORY OEM SERVICE PROCEDURE

Limp-home mode 1

Fault not caused by incorrect gear ratio or unusual shifting!Β 

Explanation of table headings and content:

  • Shift state before setting fault: States the selected position of the selector lever and the selected gear before the fault occurs and is set.
  • Step 1: After a fault occurs and is set, the Tiptronic control unit switches to limp-home mode and initiates the appropriate shift operation.
  • Step 2: The vehicle is in motion and the shift operation initiated in 'Step 1' terminates.
  • Step 3: Motion is interrupted and the vehicle stops. The Tiptronic control unit initiates the shift operation for 'gear 3' (the run will be continued in 'gear 3').
  • Step 4: The shift operation initiated in 'Step 3' terminates and 'gear 3' is engaged.
SHIFT RESPONSE OF TRANSMISSION IN LIMP-HOME MODE 1

Limp-home mode 1
Shift state before fault set Step 1 Step 2 Step 3 Step 4
Shift response Torque limit Nm Shift response Torque limit Nm Shift response Torque limit Nm Shift response Torque limit Nm
remains in gear changes gear remains in gear changes gear remains in gear changes gear remains in gear changes gear
R R B1/IN 400 state remains same 400 state remains same 400 shift solenoid valves
are
disabled**
(see notes)
400
D 1 - 3* 10 all shift solenoid valves
are
'OFF'
engaged gear held
400 3 - 400 400
D 2 - 3* 10 400 3 - 400 400
D 3 3* - 400 400 3 - 400 400
D 4 4* - 250 250 - 3** 250 400
D 5 5 - 250 250 - 3** 250 400
D 6 6 - 250 250 - 3** 250 400
'R' control enabled enabled enabled disabled
Power switch (in Tiptronic control unit ON ON ON OFF

Explanatory notes on content of table for Limp-home mode 1:Β 

Power switch (in Tiptronic control unit):Β 

With the power switch (in Tiptronic control unit) 'ON', the Tiptronic control unit can control the transmission.

With the power switch (in Tiptronic control unit) 'OFF', the Tiptronic control unit cannot control the transmission.

  • D: 'Selector lever position' gears 1, 2, 3, 4, 5, 6
  • R: 'Selector lever position' reverse gear
  • 'B1' Shift solenoid valve B1 (modulation pressure)

Where the state given in the table is shown with a '*' or '**', then the state is modified as follows:

  • *: 'Gear 5' is engaged if a fault is present in the 'shift solenoid valve C1 (modulation pressure)' (disengagement fault of the torque converter lockup clutch).
  • **: Shifting is not possible if a fault is present in the 'shift solenoid valve C2 (modulation pressure)' (engagement fault of the torque converter lockup clutch). If the selector lever is moved from 'D' to 'N' and back again to 'D', then the Tiptronic control unit shifts to 'gear 5'. Differences: If the vehicle speed = 0 km/h and the period of 10 seconds set in the selector lever positions 'P, R, N' expires, then 'gear 3' is engaged after changing the selector lever position from 'D' to 'N' and back again to 'D'. If the selector lever is moved from 'D' to 'N' and back again to 'D' in 'step 1' and 'step 2', the Tiptronic control unit shifts to 'gear 5'.

In the event of a 'solenoid valve modulation pressure (main)' fault, the torque is limited as follows:

  • Selector lever in position 'D' 150 Nm
  • Selector lever in position 'R' 100 Nm
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.