Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1999 Porsche Boxster (986) F6-2.5LFACTORY OEM SERVICE PROCEDURE
Control Module, A/T
TIPTRONIC CONNECTOR ASSIGNMENT:

Image Legend:
1 - Pressure regulator 2
2 - Shiftlock solenoid
3 - Free
4 - Pressure regulator 4
5 - Pressure regulator 1
6 - Power ground
7 - Free
8 - Multifunction switch, line 2
9 - Multifunction switch, line 4
10 - Brake light
11 - Free
12 - Pin code 1
13 - Manual program switch
14 - Output shaft speed (-)
15 - Shield, output shaft speed
16 - Turbine speed ( + )
17 - Free
18 - Kick-down
19 - TC active
20 - Free
21 - Sensor ground
22 - ATF temperature
23 - Shield, turbine speed
24 - Free
25 - Display, manual mode
26 - Terminal 30
27 - Cruise control
28 - Electronics ground
29 - Pressure regulator 3
30 - Solenoid valve 1
31 - Free
32 - Solenoid valve 3
33 - Solenoid valve 2
34 - Power ground
35 - Free
36 - Multi-function switch, line 1
37 - Multi-function switch, line 3
38 - Front-wheel speed, left
39 - Front-wheel speed, right
40 - Free
41 - Free
42 - Output shaft speed ( + )
43 - Free
44 - Ground, turbine speed
45 - Free
46 - Upshift
47 - Downshift
48 - Pin code 2
49 - Free
50 - Free
51 - Coolant shutoff valve
52 - Plus - pressure regulator, solenoid valves
53 - Plus - pressure regulator, solenoid valves, shiftiock
54 - Terminal 15
55 - Terminal 15
56 to 84 - Free
85 - CAN - low
86 - CAN - high
87 - Free
88 - K-line
Tiptronic Connector Assignment:
Image Legend:
1 - Pressure regulator 2
2 - Shiftlock solenoid
3 - Free
4 - Pressure regulator 4
5 - Pressure regulator 1
6 - Power ground
7 - Free
8 - Multifunction switch, line 2
9 - Multifunction switch, line 4
10 - Brake light
11 - Free
12 - Pin code 1
13 - Manual program switch
14 - Output shaft speed (-)
15 - Shield, output shaft speed
16 - Turbine speed ( + )
17 - Free
18 - Kick-down
19 - TC active
20 - Free
21 - Sensor ground
22 - ATF temperature
23 - Shield, turbine speed
24 - Free
25 - Display, manual mode
26 - Terminal 30
27 - Cruise control
28 - Electronics ground
29 - Pressure regulator 3
30 - Solenoid valve 1
31 - Free
32 - Solenoid valve 3
33 - Solenoid valve 2
34 - Power ground
35 - Free
36 - Multi-function switch, line 1
37 - Multi-function switch, line 3
38 - Front-wheel speed, left
39 - Front-wheel speed, right
40 - Free
41 - Free
42 - Output shaft speed ( + )
43 - Free
44 - Ground, turbine speed
45 - Free
46 - Upshift
47 - Downshift
48 - Pin code 2
49 - Free
50 - Free
51 - Coolant shutoff valve
52 - Plus - pressure regulator, solenoid valves
53 - Plus - pressure regulator, solenoid valves, shiftiock
54 - Terminal 15
55 - Terminal 15
56 to 84 - Free
85 - CAN - low
86 - CAN - high
87 - Free
88 - K-line
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
