2008 Pontiac Wave (CANADA) L4-1.6LFACTORY OEM SERVICE PROCEDURE

Disassembled Views



Disassembled Views

Case and Associated Parts (1 of 2)

Case and Associated Parts:

Factory service manual diagram



1 - Breather Hose
2 - Clip
3 - Breather Plug
4 - O-Ring
5 - Washer
6 - Drain Plug
7 - O-Ring
8 - Screw Plug
9 - O-Ring
10 - Oil Cooler Inlet Union
11 - O-Ring
12 - Oil Cooler Outlet Union
13 - Input Shaft Speed (ISS) Sensor

Case and Associated Parts (2 of 2)

Case and Associated Parts:

Factory service manual diagram



1 - Oil Seal
2 - Transaxle Housing
3 - Oil Reservoir Plate
4 - Transaxle Oil Apply Pipe
5 - Spring
6 - Check Valve Pipe Clamp
7 - Apply Gasket
8 - Brake Drum Gasket
9 - Differential Gear Oil Apply Pipe
10 - O-Ring
11 - Transaxle Wire
12 - Torsion Spring
13 - Transaxle Oil Apply Pipe Clamp
14 - Parking Lock Pawl
15 - Manual Valve Lever
16 - Spacer
17 - Oil Seal
18 - Park/Neutral Position Switch
19 - Lock Washer
20 - Control Lever
21 - Washer
22 - Spring
23 - O-Ring
24 - Overdrive Brake Accumulator Piston
25 - O-Ring
26 - Spring
27 - O-Ring
28 - Forward Clutch Accumulator Piston
29 - O-Ring
30 - O-Ring
31 - Direct Clutch Accumulator Piston
32 - O-Ring
33 - Spring
34 - Manual Detent Spring
35 - Pin
36 - Parking Lock Rod
37 - Parking Lock Pawl Shaft
38 - Manual Valve Lever Shaft
39 - Parking Lock Pawl Bracket
40 - Oil Pan
41 - Gasket
42 - Magnet
43 - Oil Strainer
44 - Gasket
45 - Valve Body

Internal Components

Internal Components:

Factory service manual diagram



1 - Planetary Ring Gear
2 - O-Ring
3 - 1st and Reverse Brake Piston
4 - O-Ring
5 - 1st and Reverse Brake Piston Return Spring
6 - Plate
7 - Disc
8 - Flange
9 - Snap Ring
10 - Planetary Gear
11 - Thrust Washer
12 - No. 2 One-Way Clutch
13 - Anti-Rattle Clip
14 - Flange
15 - Disc
16 - Plate
17 - 2nd Brake Piston Return Spring
18 - O-Ring
19 - 2nd Brake Piston
20 - O-Ring
21 - 2nd Brake Clutch Cylinder
22 - Snap Ring
23 - Thrust Bearing Race
24 - Front Planetary Sun Gear
25 - Thrust Bearing Race
26 - One-Way Clutch Assembly
27 - Thrust Washer
28 - Rear Planetary Sun Gear
29 - Snap Ring
30 - Flange
31 - Disc
32 - Plate
33 - Thrust Bearing Race
34 - Thrust Needle Roller Bearing
35 - Forward Clutch Hub
36 - Thrust Bearing Race
37 - Thrust Needle Roller Bearing
38 - Thrust Bearing Race
39 - Forward and Reverse Clutch Assembly
40 - Thrust Needle Roller Bearing
41 - Snap Ring
42 - O/D Brake Return Spring
43 - O/D Brake Piston
44 - O-Ring
45 - Seal Ring
46 - Transaxle Rear Cover
47 - Apply Gasket
48 - O-Ring
49 - Screw Plug

Differential and Oil Pump

Differential and Oil Pump:

Factory service manual diagram



1 - Side Bearing Outer Race
2 - Shim
3 - Outer Tapered Roller Bearing Race
4 - Counter Driven Gear
5 - Oil Seal
6 - Transaxle Case Plate
7 - Apply Gasket
8 - Counter Driven Gear
9 - Direct Clutch Hub
10 - Thrust Bearing Race
11 - Direct Clutch Assembly
12 - Thrust Needle Roller Bearing
13 - Differential Case
14 - Oil Pump

Bearing and Race Installation and Direction

Bearing and Race Installation and Direction:

Factory service manual diagram




Factory service manual diagram




Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.