2007 Pontiac Grand Prix BaseFACTORY OEM SERVICE PROCEDURE

Powertrain Control Module (PCM) Connector End View C3

Fig 1: PCM C3 Connector End View
GM1590596Courtesy of GENERAL MOTORS CORP.
PCM C3 Connector Part Information

Connector Part Information 
  • OEM: 15497996
  • Service: See Catalog
  • Description: 73-Way F 64 2.8 Series, Sealed (BK)
Terminal Part Information 
  • Pins: 2, 6, 11, 15, 18, 19, 22, 24, 34, 36, 38, 45, 47, 49, 51
  • Terminal/Tray: 15359541/4
  • Core/Insulation Crimp: M/M
  • Release Tool/Test Probe: 15381651-2/J-35616-64B (L-BU)
PCM C3 Connector Terminal Identification

Pin Wire Color Circuit No. Function
1-6 - - Not Used
7 RD 225 Generator Turn On Signal
8-9 - - Not Used
10 TN 5496 Cylinder Shutoff Solenoid Control 6
11 D-BU 5491 Cylinder Shutoff Solenoid Control 1
12 TN/BK 464 Delivered Torque Signal
13-16 - - Not Used
17 OG/BK 463 Requested Torque Signal
18 BN 1174 Oil Level Switch Signal
19-20 - - Not Used
21 BK 2751 Low Reference
22 - - Not Used
23 OG/BK 469 Low Reference
24-27 - - Not Used
28 RD/BK 645 Low Reference
29 GY 23 Generator Field Duty Cycle Signal
30-32 - - Not Used
33 TN 2501 High-Speed GMLAN Serial Data Bus (-)
34 - - Not Used
35 BK 2761 Low Reference
36 - - Not Used
37 GY 2700 5-Volt Reference 1
38 - - Not Used
39 GY 2704 5-Volt Reference 1
40-43 - - Not Used
44 GY 605 5-Volt Reference 2
45 - - Not Used
46 OG/BK 1786 Park/Neutral Signal
47 - - Not Used
48 D-GN/WH 428 EVAP Canister Purge Solenoid Control
49 D-GN 335 Low Speed Cooling Fan Relay Control
50-52 - - Not Used
53 TN/WH 2500 High-Speed GMLAN Serial Data Bus (+)
54 - - Not Used
55 YE 410 ECT Sensor Signal
56 - - Not Used
57 RD/BK 380 A/C Refrigerant Pressure Sensor Signal
58 - - Not Used
59 L-GN 432 MAP Sensor Signal
60-65 - - Not Used
66 RD 381 Vehicle Speed Signal
67 - - Not Used
68 WH 5497 Cylinder Shutoff Solenoid Control 7
69 OG 5494 Cylinder Shutoff Solenoid Control 3
70-73 - - Not Used
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.