Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Pontiac G5 Base, AutomaticFACTORY OEM SERVICE PROCEDURE
Powertrain Control Module (PCM) Connector End View C1
Powertrain Control Module (PCM) C1 Connector & Terminal Parts Information
Connector Part Information
|
Terminal Part Information
|
Powertrain Control Module (PCM) C1 Terminal Identification
| Pin | Wire Color | Circuit No. | Function |
|---|---|---|---|
| 1 | TN/BK | 2500 | High Speed GMLAN Serial Data (+) |
| 2 | TN | 2501 | High Speed GMLAN Serial Data (-) |
| 3-5 | - | - | Not Used |
| 6 | D-GN/WH | 459 | A/C Compressor Clutch Relay Control |
| 7 | BN | 1271 | Low Reference |
| 8 | PU | 1272 | Low Reference |
| 9 | - | - | Not Used |
| 10 | D-BU | 473 | High Speed Cooling Fan Relay Control |
| 11 | - | - | Not Used |
| 12 | PU | 1589 | Fuel Level Sensor Signal |
| 13 | PK/BK | 5293 | Ignition 1 Voltage |
| 14 | L-BU | 6118 | IAT 2 Sensor Signal |
| 15 | - | - | Not Used |
| 16 | D-GN | 1049 | ECM/PCM/VCM Class 2 Serial Data |
| 17 | GY | 2700 | 5-Volt Reference - 1 |
| 18 | BN | 4 | Accessory Voltage |
| 19 | PK/BK | 1039 | Ignition 1 Voltage |
| 20 | RD/WH | 840 | Battery Positive Voltage |
| 21 | - | - | Not Used |
| 22 | WH | 1310 | EVAP Canister Vent Solenoid Control |
| 23 | - | - | Not Used |
| 24 | D-GN | 890 | Fuel Tank Pressure Sensor Signal |
| 25 | - | - | Not Used |
| 26 | OG/BK | 380 | A/C Refrigerant Pressure Sensor Signal |
| 27 | D-BU | 1161 | APP Sensor 1 Signal |
| 28 | - | - | Not Used |
| 29 | TN | 2759 | Low Reference |
| 30 | WH/BK | 1164 | 5-Volt Reference - B |
| 31 | - | - | Not Used |
| 32 | L-BU | 20 | Stop Lamp Switch Signal |
| 33 | - | - | Not Used |
| 34 | PK | 2014 | Coolant Pump Relay Control |
| 35-36 | - | - | Not Used |
| 37 | D-GN/WH | 465 | Fuel Pump Relay Control |
| 38 | BN | 5069 | Powertrain Relay Control |
| 39 | - | - | Not Used |
| 40 | BN/WH | 419 | MIL Control |
| 41 | L-BU | 1162 | APP Sensor 2 Signal |
| 42 | - | - | Not Used |
| 43 | TN | 1274 | 5-Volt Reference - 1 |
| 44-45 | - | - | Not Used |
| 46 | PU | 420 | TCC Brake Switch/Cruise Control Release Signal |
| 47 | GY | 2709 | 5-Volt Reference - 1 |
| 48 | YE | 447 | Starter Relay Coil Control |
| 49-50 | - | - | Not Used |
| 51 | D-GN | 335 | Low Speed Cooling Fan Relay Control |
| 52 | - | - | Not Used |
| 53 | BN/WH | 379 | CPP Switch Signal |
| 54 | D-GN | 1433 | PNP/Clutch Start Switch Signal |
| 55 | - | - | Not Used |
| 56 | BK/WH | 2751 | Ground |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
