Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Pontiac G5 Base, AutomaticFACTORY OEM SERVICE PROCEDURE
Powertrain Control Module (PCM) Connector End View C2
Powertrain Control Module (PCM) C2 Connector & Terminal Parts Information
Connector Part Information
|
Terminal Part Information
|
Powertrain Control Module (PCM) C2 Terminal Identification
| Pin | Wire Color | Circuit No. | Function |
|---|---|---|---|
| 1 | RD | 225 | Generator Turn On Signal |
| 2 | D-GN | 485 | TP Sensor 1 Signal |
| 3 | - | - | Not Used |
| 4 | GY | 596 | 5-Volt Reference - 1 |
| 5 | GY | 2704 | 5-Volt Reference - 1 |
| 6 | GY | 2701 | 5-Volt Reference - 1 |
| 7 | PU | 486 | TP Sensor 2 Signal |
| 8 | D-GN | 6291 | 5-Volt Reference - 2 |
| 9 | L-BU/BK | 1688 | 5-Volt Reference - 2 |
| 10-15 | - | - | Not Used |
| 16 | PU | 6413 | Low Reference |
| 17 | YE | 573 | CKP Sensor [1] Signal |
| 18 | PU | 574 | Low Reference |
| 19 | - | - | Not Used |
| 20 | D-GN/WH | 6292 | Low Reference |
| 21 | PK/BK | 632 | Low Reference |
| 22-24 | - | - | Not Used |
| 25 | TN/WH | 1669 | HO2S Low Signal Bank 1 Sensor (2) |
| 26 | BN/WH | 633 | CMP Sensor Signal |
| 27-28 | - | - | Not Used |
| 29 | GY | 1724 | Boost Control Solenoid Control |
| 30 | OG/BK | 469 | Low Reference |
| 31 | - | - | Not Used |
| 32 | TN | 1667 | HO2S Low Signal Bank 2 Sensor (1) |
| 33 | BK | 1744 | Fuel Injector (1) Control |
| 34 | - | - | Not Used |
| 35 | YE | 410 | ECT Sensor Signal |
| 36 | BK/WH | 1704 | Low Reference |
| 37 | GY | 6337 | MAP Sensor Signal |
| 38 | L-GN | 432 | SCIP Sensor Signal |
| 39 | BK | 2752 | Low Reference |
| 40 | BN/WH | 6405 | IC 1 Control |
| 41 | YE | 492 | MAF Sensor Signal |
| 42 | D-GN/WH | 6407 | IC 4 Control |
| 43 | BK/WH | 1423 | HO2S Heater Low Control Bank 1 Sensor (2) |
| 44 | - | - | Not Used |
| 45 | GY | 23 | Generator Field Duty Cycle Signal |
| 46 | PU/WH | 1668 | HO2S High Signal Bank 1 Sensor (2) |
| 47 | - | - | Not Used |
| 48 | PU | 1666 | HO2S High Signal Bank 2 Sensor (1) |
| 49-50 | - | - | Not Used |
| 51 | TN | 472 | IAT Sensor Signal |
| 52 | BK | 2761 | Low Reference |
| 53 | L-GN/BK | 1745 | Fuel Injector 2 Control |
| 54 | L-BU/BK | 844 | Fuel Injector 4 Control |
| 55 | PK/BK | 1746 | Fuel Injector 3 Control |
| 56-57 | - | - | Not Used |
| 58 | D-GN | 676 | HO2S Heater High Control Bank 1 Sensor (1) |
| 59 | D-BU/WH | 6406 | IC 3 Control |
| 60 | L-BU/WH | 6408 | IC 2 Control |
| 61-63 | - | - | Not Used |
| 64 | BK | 2760 | Low Reference |
| 65 | BN | 582 | TAC Motor Control - 2 |
| 66 | YE | 581 | TAC Motor Control - 1 |
| 67 | - | - | Not Used |
| 68 | D-BU | 496 | Knock Sensor (1) Signal |
| 69 | GY | 1716 | Knock Sensor Signal |
| 70-72 | - | - | Not Used |
| 73 | BK/WH | 451 | Ground |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
