Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2006 Pontiac Solstice L4-2.4L VIN BFACTORY OEM SERVICE PROCEDURE
Scan Tool Data Definitions
SCAN TOOL DATA DEFINITIONS (CRUISE CONTROL)
The Scan Tool Data Definitions contains a brief description of all cruise control related parameters available on the scan tool.
CPP Switch: The scan tool displays Applied or Released. The ECM monitors the clutch pedal position (CPP) switch signal circuit. An open switch is displayed as Applied.
Cruise Control Active: The scan tool displays Yes or No. The ECM determines the current status of the cruise control operation. An operating cruise control system is displayed as Yes.
Cruise Control Switch: The scan tool displays Off/On/Error/Resume/Set. The body control module (BCM) monitors the cruise control set/coast and resume/accel switch signal circuit in order to determine the status of the cruise control switch.
Cruise Control Switch: The scan tool displays 0-5 Volts. The BCM monitors the voltage of the cruise control set/coast and resume/accel switch signal circuit. in order to determine the status of the cruise control switch. The listed values are voltage values from a known good cruise control switch. Off = 0.0 Volts/On = 0.6 Volts/Resume = 1.5 Volts/Set = 3.0 Volts.
Cruise Disengage (1-8) History: The scan tool displays the last 8 reasons why the cruise control system was disengaged. Refer to the Scan Tool Data Definitions (Disengage History) for descriptions. Scan Tool Data Definitions (Disengage History)
Cruise On/Off Switch: The scan tool displays On/Off. This is the state of the cruise control On/Off switch as detected by the ECM. An active switch is displayed as On.
Cruise Resume/Accel Switch: The scan tool displays On or Off. This is the state of the resume/accel switch as detected by the ECM. An active cruise resume and accel switch is displayed as On. The cruise control On/Off switch must be On to view the parameter correctly.
Cruise Set/Coast Switch: The scan tool displays On or Off. This is the state of the cruise set switch as detected by the ECM. An active cruise set switch is displayed as On. The cruise control On/Off switch must be On to view the parameter correctly.
Engine Speed: The scan tool displays 0 to 9999 RPM. This is the engine RPM as monitored by the ECM. The ECM monitors the crankshaft position (CKP) signal circuit in order to determine the engine RPM.
Ignition 1 Signal: The scan tool displays 0 to 25.5 Volts. The ECM monitors the voltage of the ignition 1 voltage circuit.
Traction Control Status: The scan tool displays Active or Inactive. When the ECM detects that a traction control condition exists, the scan tool displays Active.
Vehicle Speed Sensor: The scan tool displays 0-255 km/h (0-155 mph). The ECM monitors the vehicle speed sensor signal in order to calculate the vehicle speed for display.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.