Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2003 Pontiac Sunfire L4-2.2L VIN FFACTORY OEM SERVICE PROCEDURE
Piston, Engine
Piston Diameter @ 14.5 mm up 85.967-85.982 mm (13.3845-3.3851 inch)
Piston to Bore Clearance 0.010-0.041 mm (0.0004-0.0016 inch)
Piston Weight
Piston Height Max. 0.9 mm-below deck
Piston Pin Bore I.D. 20.002-20.007 mm (0.7875-0.7877 inch)
Ring Groove Width, Top 1.23-1.25 mm (0.0484-0.0492 inch)
Ring Groove Width, Second 1.52-1.54 mm (0.0598-0.0606 inch)
Ring Groove Width, Oil Control 2.52-2.54 mm (0.0992-0.1000 inch)
Piston Ring Thickness, Top 1.170-1.190 mm (0.0461-0.0469 inch)
Piston Ring Thickness, Second 1.471-1.490 mm (0.0579-0.0587 inch)
Piston Ring Thickness, Oil Control Rail 0.43 mm max. (0.0169 in max.)
Piston Ring Thickness, Oil Control Spacer 1.574-1.651 mm (0.0620-0.0650 inch)
Ring to Groove Clearance, Top 0.04-0.08 mm (0.0015-0.0031 inch)
Ring to Groove Clearance, Second 0.030-0.069 mm (0.0012-0.0027 inch)
Ring to Groove Clearance, Oil Control 0.090-0.106 mm (0.0035-0.0042 inch)
Ring Gap, Top 0.20-0.40 mm (0.008-0.016 inch)
Ring Gap, Second 0.35-0 55 mm (0.014-0.022 inch)
Ring Gap, Oil Rails 0.25-0.76 mm (0.010-0.030 inch)
Piston to Bore Clearance 0.010-0.041 mm (0.0004-0.0016 inch)
Piston Weight
Piston Height Max. 0.9 mm-below deck
Piston Pin Bore I.D. 20.002-20.007 mm (0.7875-0.7877 inch)
Ring Groove Width, Top 1.23-1.25 mm (0.0484-0.0492 inch)
Ring Groove Width, Second 1.52-1.54 mm (0.0598-0.0606 inch)
Ring Groove Width, Oil Control 2.52-2.54 mm (0.0992-0.1000 inch)
Piston Ring Thickness, Top 1.170-1.190 mm (0.0461-0.0469 inch)
Piston Ring Thickness, Second 1.471-1.490 mm (0.0579-0.0587 inch)
Piston Ring Thickness, Oil Control Rail 0.43 mm max. (0.0169 in max.)
Piston Ring Thickness, Oil Control Spacer 1.574-1.651 mm (0.0620-0.0650 inch)
Ring to Groove Clearance, Top 0.04-0.08 mm (0.0015-0.0031 inch)
Ring to Groove Clearance, Second 0.030-0.069 mm (0.0012-0.0027 inch)
Ring to Groove Clearance, Oil Control 0.090-0.106 mm (0.0035-0.0042 inch)
Ring Gap, Top 0.20-0.40 mm (0.008-0.016 inch)
Ring Gap, Second 0.35-0 55 mm (0.014-0.022 inch)
Ring Gap, Oil Rails 0.25-0.76 mm (0.010-0.030 inch)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
