Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2003 Pontiac Sunfire L4-2.2L VIN FFACTORY OEM SERVICE PROCEDURE
Body Control Module (BCM)
BODY CONTROL MODULE
The various BCM input and output circuits are described in the corresponding functional areas indicated on the BCM electrical schematics. The Body Control Module functions include the following.
- Retained Accessory Power, RAP, Audio System only.
- A/C compressor request.
- Remote Function Control.
- A/C cooling Fan.
- Exterior and interior lighting control
- Daytime running lights (DRL)
- Automatic lighting control
- Fog lamps
- Interior lighting.
- Battery rundown protection (Inadvertent Power).
- Chimes.
- Key In Ignition
- Head Lamps On
- Seat Belt Not Fastened
- Turn Signal On
- Park Brake Warning
- Door Ajar Warning
- Check gauges
- Gauge control.
- Instrument cluster indicator control.
- Theft deterrent.
- Engine coolant level sensing.
- Key-in-ignition sensing.
- Brake fluid level sensing.
- Parking brake state sensing.
- Rear compartment interface.
- Horn interface.
- Door lock interface.
- Bulb Check.
- ETS -Pontiac Only.
- A/T Shift lock control.
The BCM contains the logic of the theft deterrent system. The BCM provides the battery positive voltage to operate the Passlock(TM) Sensor. The BCM also measures the voltage of the security sensor signal circuit. The voltage measured will indicate whether the Passlock(TM) Sensor has been activated and whether the resistance value from the sensor is a valid value or the tamper value. If voltage measured is in the valid range, the BCM compares this voltage, voltage code, to a previously learned voltage code. If the voltage codes match, the BCM sends a class 2 message containing a password to the PCM. If the voltage codes do not match, or the voltage is in the Tamper range, or there is a circuit fault, the BCM will not send the correct password to the PCM, and the vehicle will not start.
The various BCM input and output circuits are described in the corresponding functional areas indicated on the BCM electrical schematics. The Body Control Module functions include the following.
- Retained Accessory Power, RAP, Audio System only.
- A/C compressor request.
- Remote Function Control.
- A/C cooling Fan.
- Exterior and interior lighting control
- Daytime running lights (DRL)
- Automatic lighting control
- Fog lamps
- Interior lighting.
- Battery rundown protection (Inadvertent Power).
- Chimes.
- Key In Ignition
- Head Lamps On
- Seat Belt Not Fastened
- Turn Signal On
- Park Brake Warning
- Door Ajar Warning
- Check gauges
- Gauge control.
- Instrument cluster indicator control.
- Theft deterrent.
- Engine coolant level sensing.
- Key-in-ignition sensing.
- Brake fluid level sensing.
- Parking brake state sensing.
- Rear compartment interface.
- Horn interface.
- Door lock interface.
- Bulb Check.
- ETS -Pontiac Only.
- A/T Shift lock control.
The BCM contains the logic of the theft deterrent system. The BCM provides the battery positive voltage to operate the Passlock(TM) Sensor. The BCM also measures the voltage of the security sensor signal circuit. The voltage measured will indicate whether the Passlock(TM) Sensor has been activated and whether the resistance value from the sensor is a valid value or the tamper value. If voltage measured is in the valid range, the BCM compares this voltage, voltage code, to a previously learned voltage code. If the voltage codes match, the BCM sends a class 2 message containing a password to the PCM. If the voltage codes do not match, or the voltage is in the Tamper range, or there is a circuit fault, the BCM will not send the correct password to the PCM, and the vehicle will not start.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
