Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2003 Pontiac Sunfire L4-2.2L VIN FFACTORY OEM SERVICE PROCEDURE
Scan Tool Data Definitions
SCAN TOOL DATA DEFINITIONS
Use the Scan Tool Data Display Values and Definitions Information in order to assist in diagnosing vehicle malfunctions. Compare the vehicles actual scan tool data with the typical data display value table information. Use the data information in order to aid in understanding the nature of the problem when the vehicle does not match with the typical data display values.
The scan tool data values were taken from a known good vehicle under the following conditions:
- The ignition switch is in the ON position.
- The engine is not running.
- The vehicle is in PARK.
A/C Request: The BCM uses this input to determine the position of the air conditioning switch. YES is displayed when a/c is requested.
Accessory: The BCM uses this data in order to determine the position of the ignition switch. ON is displayed when the ignition switch is in the ON or ACCY position.
Battery Voltage: This voltage value refers to the battery system voltage.
Brake Fluid Level Switch: The BCM uses this input to determine the position of the brake fluid level switch. ON is displayed when a low brake fluid condition exists.
Calibration ID: This information refers to how the BCM is calibrated. This information is for assembly plant use only.
Ignition 1: The BCM uses this data in order to determine the position of the ignition switch. ON is displayed when the ignition switch is in the ON or CRANK position.
Key In Ignition: This information refers to whether or not the ignition key is inserted into the ignition switch. The BCM uses this data to perform chime functions. ON is displayed when the key is inserted into the ignition switch.
Last 4 Dig. of GM Part #: This information refers to the last 4 digits of the GM BCM part number that is currently in the vehicle. Low Coolant Level The BCM uses this input to determine the position of the coolant level switch. ON is displayed when a low coolant level condition exists.
Model Year: This information refers to the model year of the vehicle.
Panic Horn Relay: This output displays whether or not the BCM is providing ground for the horn relay. ON is displayed when the BCM is providing ground for the relay.
Panic Horn Relay Feedback: This input displays the state of the horn relay. When the horn switch is pressed, ACTIVE is displayed.
Park Brake Switch: The BCM uses this input to determine the position of the rear park brake switch. ON is displayed when the park brake is applied.
Park (BTSI) Relay: This output displays whether or not the BCM is providing ground for the A/T shift lock control solenoid. ON is displayed when the BCM is providing ground for the solenoid.
Park (BTSI) Relay Feedback: This input displays the state of the A/T shift lock control solenoid. ACTIVE is displayed when the BCM is commanding the solenoid to lock the gear select lever.
Traction Switch: The BCM uses this input to determine the position of the traction control switch. ON is displayed when the enhanced traction system is active.
Year Module Built: This information refers to the year that the BCM was built.
Use the Scan Tool Data Display Values and Definitions Information in order to assist in diagnosing vehicle malfunctions. Compare the vehicles actual scan tool data with the typical data display value table information. Use the data information in order to aid in understanding the nature of the problem when the vehicle does not match with the typical data display values.
The scan tool data values were taken from a known good vehicle under the following conditions:
- The ignition switch is in the ON position.
- The engine is not running.
- The vehicle is in PARK.
A/C Request: The BCM uses this input to determine the position of the air conditioning switch. YES is displayed when a/c is requested.
Accessory: The BCM uses this data in order to determine the position of the ignition switch. ON is displayed when the ignition switch is in the ON or ACCY position.
Battery Voltage: This voltage value refers to the battery system voltage.
Brake Fluid Level Switch: The BCM uses this input to determine the position of the brake fluid level switch. ON is displayed when a low brake fluid condition exists.
Calibration ID: This information refers to how the BCM is calibrated. This information is for assembly plant use only.
Ignition 1: The BCM uses this data in order to determine the position of the ignition switch. ON is displayed when the ignition switch is in the ON or CRANK position.
Key In Ignition: This information refers to whether or not the ignition key is inserted into the ignition switch. The BCM uses this data to perform chime functions. ON is displayed when the key is inserted into the ignition switch.
Last 4 Dig. of GM Part #: This information refers to the last 4 digits of the GM BCM part number that is currently in the vehicle. Low Coolant Level The BCM uses this input to determine the position of the coolant level switch. ON is displayed when a low coolant level condition exists.
Model Year: This information refers to the model year of the vehicle.
Panic Horn Relay: This output displays whether or not the BCM is providing ground for the horn relay. ON is displayed when the BCM is providing ground for the relay.
Panic Horn Relay Feedback: This input displays the state of the horn relay. When the horn switch is pressed, ACTIVE is displayed.
Park Brake Switch: The BCM uses this input to determine the position of the rear park brake switch. ON is displayed when the park brake is applied.
Park (BTSI) Relay: This output displays whether or not the BCM is providing ground for the A/T shift lock control solenoid. ON is displayed when the BCM is providing ground for the solenoid.
Park (BTSI) Relay Feedback: This input displays the state of the A/T shift lock control solenoid. ACTIVE is displayed when the BCM is commanding the solenoid to lock the gear select lever.
Traction Switch: The BCM uses this input to determine the position of the traction control switch. ON is displayed when the enhanced traction system is active.
Year Module Built: This information refers to the year that the BCM was built.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
