Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2002 Pontiac Firebird Formula, AutomaticFACTORY OEM SERVICE PROCEDURE
Checking Fluid Levels
NOTE:
The transmission fluid may darken with normal use and does not always indicate contamination or oxidation.
- Start the engine and operate the vehicle for 15 minutes or until the transmission fluid reaches an operating temperature of 82-93°C (180-200°F). Park the vehicle on a level surface. With your foot on the brake, move the shift lever through each gear range. Pause for about 3 seconds in each range, ending in Park. Apply the parking brake and let the engine idle for 3 minutes. Remove the transmission fluid level indicator. Wipe the indicator clean. Reinsert the indicator. Give the indicator a full twist in order to close. Wait 3 seconds and remove the indicator. Read both sides of the indicator. The fluid must be within the hot cross-hatched area using the lowest level reading.
- Check the fluid color. Is the fluid red in color? If so, go to step 6 . If not, go to next step.
- Is the fluid a non-transparent pink in color? If so, go to step 15 . If not, go to next step.
- Is the fluid a light brown in color? If not, go to step 6 . If so, go to next step.
- Is the fluid black in color and or have a "burnt" smell? If so, go to step 15 . If not, go to next step.
- Does the fluid appear as a solid "liquid" and not "foamy" or full of bubbles on level indicator? If not, go to step 8 . If so, go to next step.
- Check the fluid level. Proper level should be in middle of the "X" pattern, on level indicator. Is the level OK? If so, go to step 20 . If not, go to next step.
- Is the fluid level high on indicator? If so, go to step 13 . If not, go to next step.
- Is the fluid level low on indicator? If not, go to step 5 . If so, go to next step.
- Check for any external leak or leaks. Did you find an external leak or leaks? If not, go to step 12 . If so, go to next step.
- Correct leak or leaks as needed. Are any leak or leaks still present? If so, go to step 10 . If not, go to next step.
- Add fluid until level is in middle of "X" pattern on the level indicator. Is the level OK? If not, go to step 7 . If so, go to step 20 .
- Drain fluid until level is in middle of "X" pattern on the level indicator. Is level OK? If not, go to step 7 . If so, go to step 20 .
- Replace oil cooler and flush lines. See TRANSMISSION FLUID COOLER HOSE/PIPE under REMOVAL & INSTALLATION. Is the replacement complete? If so, go to step 16 .
- Drain fluid and remove oil pan to inspect. See DRAINING & REFILLING . Is there sign or signs of internal component damage noted in bottom of transmission oil pan? If not, go to step 14 . If so, go to step 17 .
- Replace the filter and fluid. See DRAINING & REFILLING . Is the replacement complete? If so, go to step 7 .
- Flush oil cooler and lines. See OIL COOLER FLUSHING and TRANSMISSION & OIL COOLER FLOW CHECK . Is the automatic transmission oil cooler flushing and flow test complete? If so, go to next step.
- Overhaul transmission. See appropriate OVERHAUL article. Is the transmission overhaul procedure complete? If so, go to next step.
- Add new fluid. Is the procedure complete? If so, go to step 7 .
- Check the fluid level and correct as necessary. Is the fluid level satisfactory? If so, system is okay. If not, go to step 1 .
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
