Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2002 Pontiac Aztek V6-3.4L VIN EFACTORY OEM SERVICE PROCEDURE
OnStar - VCU or VIU Reprogramming
ONSTAR MODULE REPROGRAMMING
IMPORTANT: Follow the instruction set for the part that you are replacing. Failure to perform these steps will prevent the OnStar features from functioning and will result in a customer return for repair.
VEHICLE INTERFACE UNIT (VIU)
1. Record the STID number from the label on the new module (10 Digits).
2. Install the new VIU.
3. After replacement, press and hold the OnStar End Call" button (black with white dot); watch for the OnStar status light to change from Green to Red to Green.
4. Move the vehicle outside and let it run for ten minutes.
5. Press the blue OnStar button twice to connect to OnStar. Tell the advisor that this vehicle has a new VIU and a new STID number to put in the customers account and that the vehicle requires a "Reconfiguration".
6. The OnStar Advisor will reconfigure the vehicle with you. Once the advisor completes configuration, you can end the call. Follow any additional instructions given by the Advisor.
7. The old VIU must be returned for core credit with the address label included in the original box. Failure to return core will result in a debit.
VEHICLE COMMUNICATION UNIT (VCU)
1. Record the ESN number from the label on the new part, (11 digits, no letters).
2. Install the new VCU.
3. After replacement, press and hold the OnStar "End Call" button (black with white dot); watch for the OnStar status light to change from Green to Red to Green.
4. Move the vehicle outside and let it run for ten minutes.
5. Press the blue OnStar button to connect to OnStar. Tell the advisor that this vehicle has a new VCU and a new ESN to put in the customers account and that the vehicle requires a "Reconfiguration". Follow any additional instructions given by the Advisor.
6. The old VCU must be returned for core credit. Use the address label included in the original box. Failure to return core will result in a debit.
IMPORTANT: Follow the instruction set for the part that you are replacing. Failure to perform these steps will prevent the OnStar features from functioning and will result in a customer return for repair.
VEHICLE INTERFACE UNIT (VIU)
1. Record the STID number from the label on the new module (10 Digits).
2. Install the new VIU.
3. After replacement, press and hold the OnStar End Call" button (black with white dot); watch for the OnStar status light to change from Green to Red to Green.
4. Move the vehicle outside and let it run for ten minutes.
5. Press the blue OnStar button twice to connect to OnStar. Tell the advisor that this vehicle has a new VIU and a new STID number to put in the customers account and that the vehicle requires a "Reconfiguration".
6. The OnStar Advisor will reconfigure the vehicle with you. Once the advisor completes configuration, you can end the call. Follow any additional instructions given by the Advisor.
7. The old VIU must be returned for core credit with the address label included in the original box. Failure to return core will result in a debit.
VEHICLE COMMUNICATION UNIT (VCU)
1. Record the ESN number from the label on the new part, (11 digits, no letters).
2. Install the new VCU.
3. After replacement, press and hold the OnStar "End Call" button (black with white dot); watch for the OnStar status light to change from Green to Red to Green.
4. Move the vehicle outside and let it run for ten minutes.
5. Press the blue OnStar button to connect to OnStar. Tell the advisor that this vehicle has a new VCU and a new ESN to put in the customers account and that the vehicle requires a "Reconfiguration". Follow any additional instructions given by the Advisor.
6. The old VCU must be returned for core credit. Use the address label included in the original box. Failure to return core will result in a debit.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
